|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
04-21-2023, 01:20 PM
|
#3 | ||||||
|
What is the point? Why spend money for tubes to shoot a more expensive shell with less shot? If you want to shoot 3/4-ounce of shot just shoot 3/4-ounce 20-gauge shells. Back when your VH was made our ammunition manufacturers offered several 3/4-ounce 20-gauge loads.
NITRO CLUB 20-gauge, Load No. X21D6.jpg Nitro Club 20-gauge 01.jpg |
||||||
|
|
||||||
 |
 |
 |
| The Following 14 Users Say Thank You to Dave Noreen For Your Post: |
|
|
|
04-21-2023, 05:11 PM
|
#4 | ||||||
|
Because I have a lot of 28 gauge ammo and don't have a 28 gauge Parker?
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to J. Scott Hanes For Your Post: |
|
|
|
04-21-2023, 06:11 PM
|
#5 | ||||||
|
Briley makes shorty tubes also well atleast for the 12 gauge perhaps they make shorties for the 20 as well .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to CraigThompson For Your Post: |
|
|
|
04-22-2023, 04:17 AM
|
#6 | ||||||
|
20 to 28 tubes are fragile. I would not do the 20 to 28 thing.
|
||||||
|
|
|
||||||
|
|
|
| The Following 5 Users Say Thank You to Bill Murphy For Your Post: |
|
|
|
04-22-2023, 06:59 AM
|
#7 | ||||||
|
Sell the 28 ga. ammo and reinvest the money into 20 ga. ammo…
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 10 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
04-22-2023, 10:38 AM
|
#8 | ||||||
|
When tubing a gun you need to go down two sizes for best results. So a 12 to 20 is fine. 16 to 28. 20 to .410. For certain bore sizes you can get away with dropping one size, but it's not optimal.
I use Briley for any full-length tubes. They custom fit the tubes for a specific bbl set. I also have them make the tubes with fixed chokes. |
||||||
|
|
|
||||||
|
|
|
| The Following 5 Users Say Thank You to Mike Koneski For Your Post: |
|
|
|
04-22-2023, 01:18 PM
|
#9 | |||||||
|
Quote:
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
|||||||
|
|
|
|||||||
|
|
|
|
|
|
04-22-2023, 03:36 PM
|
#10 | ||||||
|
I just had Briley do a set of full length 28ga for my Parker 16Ga Damascus gun. I like it quite a bit, with 3/4oz loads it breaks clays well.
__________________
Keavin Nelson |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to keavin nelson For Your Post: |
 |
|
|
Linear Mode
