|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Visit Brian Dudley's homepage! | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
10-03-2022, 09:10 AM
|
#3 | ||||||
|
Get some "Hot Stuff Glue" and glue it back on.
|
||||||
|
|
||||||
 |
 |
 |
| The Following User Says Thank You to Buddy Marson For Your Post: |
|
|
|
10-03-2022, 03:40 PM
|
#4 | ||||||
|
What they said. Use a good grade, and my advice would be to not use a thickened grade. As close as that should fit, a thin glue will bond well and not squeeze out a permanent glue line. A lot of people don't know that art woodworkers often use superglue as a finish on wood turnings. They put a light coat on a pad and pressure it against the turning. It smooths out and the mild heat generated cures the glue instantly and it takes on a nice sheen, much like an oil finish. That doesn't look like a supergloss finish. If it were me, I would use a thin SG, apply the piece and hold it in an upright position so any runs are on the inside (with masking tape added close on both sides as a block). As soon as the glue is holding, wipe off any runs, remove the tape and polish the finish all around with a soft cloth and a goodly amount of hand pressure. Use a little gunstock polish and wax to finish if needed.
|
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Arthur Shaffer For Your Post: |
|
|
|
10-03-2022, 06:35 PM
|
#5 | ||||||
|
Thank you all for your comments! I am a little worried that I will screw it up.
I'll try the thin set and mask it up with some blue tape. I will try to suck up the glue in a tuberculin syringe. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-03-2022, 09:14 PM
|
#6 | ||||||
|
You might want to practice on a scrap piece of hardwood that has very small cracks. & chips. Thin superglue is very thin and will run places you don’t expect.
Chip like that I would use a thicker grade Superglue. Put a small puddle on a jar lid etc, use a small needle, pick up a dot of glue and place it on the upright forend. Larger chip more dots. With a tweezer place the chip in place most fingers too big not precise enough. Hobby shops best source of super glues in various viscosity William |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to William Davis For Your Post: |
|
|
|
10-08-2022, 09:45 PM
|
#7 | ||||||
|
Scott, pm me. I fix this kind of stuff all the time. I use the Hot stuff, and it works great, while remaining undetectable when finished
Chris, AZ |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-08-2022, 11:04 PM
|
#8 | ||||||
|
I have used the Satellite City cyanoacrylates for many years for repairs like this. Great stuff.
https://www.caglue.com/HK-1-bHot-Stu...nder_p_39.html |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-09-2022, 11:38 AM
|
#9 | ||||||
|
There was a chip reglued very poorly in my Knick forend when I got it; I sent it to Mark Larson and the repair disappeared. Just a suggestion in case you screw it up
 .
__________________
It ain't what you don't know that gets you into trouble. It's what you know for sure that just ain't so. - Mark Twain. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-21-2022, 03:09 PM
|
#10 | ||||||
|
I was very nervous about messing it up...Brian Dudley is going to try his hand at it.
|
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
