16 ga Repro

[SXS OHIO]

CSMC had Merkel make up a batch of 16ga. 28" barrels...I bought one new set and had them fitted to my repro. The rib matting is not like the repro or the originals but is nice. Dolls head does not fit its cut in the receiver perfect but is O.K. The bores are perfect! The gun realy patterns well...I can kill wild pheasants clean at 50 yards with Fiocchi HV 5# and have done it several times with witnesses! I love them barrels! I also own all three of the original PR Kreghoff sets choked Q1/Q2, IC/Mod, Mod/Full The PR full is only .026 and the Mrekel set the full is .031 or X-full (-: thanks all SXS ohio

[MD*GSP]

Originally Posted by Kenny Graft

CSMC had Merkel make up a batch of 16ga. 28" barrels...I bought one new set and had them fitted to my repro. The rib matting is not like the repro or the originals but is nice. Dolls head does not fit its cut in the receiver perfect but is O.K. The bores are perfect! The gun realy patterns well...I can kill wild pheasants clean at 50 yards with Fiocchi HV 5# and have done it several times with witnesses! I love them barrels! I also own all three of the original PR Kreghoff sets choked Q1/Q2, IC/Mod, Mod/Full The PR full is only .026 and the Mrekel set the full is .031 or X-full (-: thanks all SXS ohio

You are fortunate to have all of those bbls - by your posts it appears you have a very very nice collection.

I can attest to the fact that Merkel bbls are beutifully made & the 16 hits hard.

That has been my go to Pheasant gun when I'm fortunate enough to hunt them (Merkel 16 - choked IC/Mod)

A marriage between Merkel & these Parker Repro's seems to be a pretty nice matchup but of the few I've seen w/the after market bbls, the dolls head is a poor fit with gaps toward the muzzle. (I know metal 'could' be welded in and refit etc)

That just bugs me to no end.

I guess that would keep the cost of fitting down eliminating some handwork but still..why go that far (making the bbls) and not go all the way? That matters to this market & by all accounts the Repros were built to pretty tight tolerances & rather good repeatability.

..sign of the times I suppose

[David C Porter]

How well does the rib matting on the Krieghoff barrels match the Parker barrel rib matting?

[Wild Skies]

The Krieghoff rib matting is not the same as the Parker Reproduction rib matting. Most owners of these bi-gauge sets have reported that they find the 16-ga. Krieghoff ribs attractive and not objectionable. IMO, it would be preferable if they were an exact match, but they are what they are.

Zoom in on the attached pic and decide for yourself.

[David C Porter]

Thanks for the info & picture

[MD*GSP]

Picture 1 shows a typical PR rib pattern.

Picture 2 shows the rib pattern on factory PR 16ga barrels made by Krieghoff.


The rib matting on both barrels is aesthetically pleasing, functional, and well executed.

[MD*GSP]

Picture 1 shows a typical PR rollmark

Picture 2 shows a legitimate 16ga PR rollmark

[MD*GSP]

Picture 1 shows legitimate Parker Reproduction 16ga barrel flats

Picture 2 shows the PR 16ga barrels origin roll mark

[Phil Cloninger]

Originally Posted by Bob Jurewicz

They are marked in script on the left side of the barrel "Parker Reproduction" and stamped "Krieghoff Ulm" on the left barrel flat.
Bob Jurewicz

I have had a couple 20/16 sets over the years, with the Krieghoff barrels, fitted by Reagent, and numbered to the gun. They were marked just as Bob had mentioned earlier in the thread, with the Made in Germany on the right barrel. The ribs on the 16 ga. barrels were wider than the original 20 ga. barrels. The matting was a bit more course on the 16 set. The difference didn't bother me at all, and to be honest, I hadn't even noticed it until I read this thread...