|
 |
 |
|||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||
 |
 |
10-13-2020, 08:25 AM
|
#3 | ||||||
|
Guess not.
I have the three screws out. But I am unable to get the plate loose. Is there a trick to it? Thanks |
||||||
|
|
||||||
 |
 |
 |
|
|
|
10-13-2020, 08:45 AM
|
#4 | ||||||
|
Through the slot in the frame that the barrel lug fits into you can tap the plate from above using a wooden dowel and a light mallet. It should then drop out easily.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-13-2020, 08:49 AM
|
#5 | ||||||
|
Careful not to use a sonic cleaner on those side plates. This practice is reported to break/fracture the springs.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-13-2020, 09:06 AM
|
#6 | ||||||
|
Thanks, that is what I needed.
Interesting about the sonic cleaner. I have not had any issues in the past. Thanks, I have some small brushes that can do the job. Dwight |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to dwight springthorpe For Your Post: |
|
|
|
10-13-2020, 03:39 PM
|
#7 | ||||||
|
The trigger plates on hammer guns are usually VERY tightly fit into the frame. More so than the hammerless guns. I don't think there was one yet that I have broken down that came apart easily.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Brian Dudley For Your Post: |
|
|
|
10-13-2020, 05:21 PM
|
#8 | ||||||
|
OK, guessing I should have removed the barrel lug prior to this. I see a pin that is hidden by the side plate. I assume that holds the lug in place and I should remove it and that will open up the slot to tap on the trigger plate. Right?
Thanks for your help. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-13-2020, 05:42 PM
|
#9 | ||||||
|
No.... you should be able to fit a rod or doewl in there to tap out the trigger plate.
Right down through that rectangular opening where you can see the yellow towel is where you will put the dowel through and tap out the trigger plate. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
10-13-2020, 05:53 PM
|
#10 | ||||||
|
 OK, I see what you mean now. I got it out, just as you said it would. You are great! Dwight |
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to dwight springthorpe For Your Post: |
 |
|
|
Linear Mode
