|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
07-12-2017, 09:04 AM
|
#3 | ||||||
|
Fleming Traps They have powder and liquid.
|
||||||
|
|
||||||
 |
 |
 |
| The Following User Says Thank You to Dennis Yager For Your Post: |
|
|
|
07-12-2017, 10:48 AM
|
#4 | ||||||
|
Ebay. For dying traps. Very cheap.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Brian Dudley For Your Post: |
|
|
|
07-12-2017, 10:50 AM
|
#5 | ||||||
|
Or use your own Hemlock bark. That's what I did when I would boil my traps back in the 50' & 60's and it produced a very black stain.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
07-13-2017, 11:19 PM
|
#6 | ||||||
|
Hey Harry. I was able to get this without logwood. Plenty black enough, and the crolle is full, but the steel should come out more, but that's not related to the use of logwood. Will probably etch again. The fine layers of this one have been a pain.
Like many of the other process variables, some evidently don't use logwood. I'd like to, to save some rusting cycles, but I'm not done setting up a tank for it. If you have time, let's reconnect and compare notes again. I've been using a slurry similar to calcium carbonate as a step late in the cycle. |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Bill Graham For Your Post: |
|
|
|
07-14-2017, 08:50 AM
|
#7 | ||||||
|
Those look good Bill.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Brian Dudley For Your Post: |
|
|
|
07-22-2017, 04:19 PM
|
#8 | ||||||
|
I've tried the logwood available on Amazon to my disappointment. The following is what I tried today without ferrous sulfate added to the logwood boil or the ferrous sulfate dip afterward as both had caused failures in the past. I'm going to try to post yesterdays pictures prior to todays plus some self explanatory stuff.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
07-22-2017, 04:24 PM
|
#9 | ||||||
|
Well, I screwed that up. Pictures 4 & 6 are correct for after logwood boil and the other two are different guns altogether from yesterday. Anyway the two correctly pictured barrels are proof that parents let their children use old Parkers as baseball bats.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Harry Collins For Your Post: |
|
refurish bbl | |
|
07-23-2017, 03:14 PM
|
#10 | ||||||
|
refurish bbl
Harry
Jim Despagno has advised me you do bbl restorations , and I have a bbl I need looked after , would you assist me , ?? Jim and are are good friends . he will vouch for me , what I have is a g grade lifter bbl with a mild dent about 10inches from the chamber of the bbl or bottom of the bbl. Call me 508 366 4588 . thank you Dave Kerns |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to davidkerns For Your Post: |
 |
|
|
Linear Mode
