|
 |
 |
|||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||
 |
 |
08-06-2016, 12:13 PM
|
#13 | ||||||
|
True
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE |
||||||
|
|
||||||
 |
 |
 |
|
|
|
08-06-2016, 03:59 PM
|
#14 | ||||||
|
Guess only it's the resin. Wood can vary depending on location on the tree, time of the year it's cut , or even location same board . Figure generaly has more resin than straight grain too.
It's not a precise science William |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to William Davis For Your Post: |
|
|
|
08-18-2016, 02:38 PM
|
#15 | ||||||
|
I've bent a number of stocks. After cracking one I pay close attention to the flow of the grain threw the wrist area. I'm usually bending mine down and sometimes the grain goes out the top of the wrist so I would be outing a lot of stress on it. Those I don't bend any more. I made up a jig, think Mike posted it on a different web site years ago. I think a safer way is as my friend does. He puts the gun on a work table with a couple bags of shot holding it there with the stock hanging over the end. Heat lamps are close to the wrist and one bag of shot is put on the end of the stock. A measurement is taken and he sits there reloading watching the stock. When it moves enough he takes the lamps away. I had a 1894 Remington that would move like a rubber hose when hot - but the damn thing would go right back. Tried it three times, even left it under tension till the next day - still went back. Did a Browning O/U for a friend. He wanted a 1/4" of cast. It cracked. I couldn't believe it. Had to epoxy and pin it back together. Lucky you couldn't see it when it was done. That one isn't gonna be bent anymore. Over at the Michigan state trap shoot guys will bend them while you wait - with no guarantees they won't crack. I don't do it anymore for other people, just myself. Like most things, it's a learning process.
__________________
Paul Harm |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Paul Harm For Your Post: |
|
|
|
08-20-2016, 08:40 AM
|
#16 | ||||||
|
I have a very straight Fox A, that I would like bent, who is recommended?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-20-2016, 11:28 AM
|
#17 | ||||||
|
if I have the name correct - Mike Oloen. Go over to http://www.doublegunshop.com and ask your question.
__________________
Paul Harm |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Paul Harm For Your Post: |
|
|
|
08-20-2016, 01:06 PM
|
#18 | ||||||
|
Yup, it's Mike Orlen in Amherst MA.
I was at his shop two weeks ago for some choke work on another member's gun. Mike is a super nice guy! Very quiet and unassuming. He did a great job for me. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
09-11-2016, 09:00 PM
|
#19 | ||||||
|
Dean, might you have a number for him?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
09-11-2016, 09:03 PM
|
#20 | ||||||
|
Mike Orlen, Amherst, MA, 413-256-1630
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
