|
 |
 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
08-14-2022, 07:03 PM
|
#3 | ||||||
|
The Parker Story says the guns is listed in the Stock Books with a Quality code of "PTX." Forty-one are 12-gauge, 23 with 30-inch barrels & 18 with 28-inch barrels. Two of the forty-one had surfaced at the time TPS was written, this gun Puglisi has 173901 and 173980. Also, seven are in the stock books listed as 10-gauge, four with 30-inch & three 32-inch.
|
||||||
|
|
||||||
 |
 |
 |
| The Following 2 Users Say Thank You to Dave Noreen For Your Post: |
|
|
|
08-14-2022, 08:39 PM
|
#4 | ||||||
|
The frame sizes were pretty much what the leftover Twist barrels were. If Twist barrels were #1 frame size, a 16 gauge #1 Trojan frame was used. If Twist barrels were #2 frame size either 12 gauge or 10 gauge, a 12 gauge #2 Trojan frame was used.
|
||||||
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Bill Murphy For Your Post: |
|
|
|
08-15-2022, 09:16 AM
|
#5 | ||||||
|
Yes, there was a batch of them made up like that. 1 frame twist trojans. As I recall, one of our members had one of them. Was it Jim Hall?
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
|
|
|
08-15-2022, 12:23 PM
|
#6 | ||||||
|
Yes. 1 frame twist. You fit a pair of 1 frame 16s to it.also.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-15-2022, 03:09 PM
|
#7 | ||||||
|
luckey you....2 guns in one always interested me....will a 2 frame 10 hammerless be able to wear 2 frame 12 ga barrels...and then would 2 frame 16 and 20 ga fit the 2 frame 10 ga....just wondering......charlie
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-15-2022, 05:21 PM
|
#8 | ||||||
|
It would be close. Firing pins would line up. Where are you planning to get a set of #2 frame 16 or 20 gauge barrels?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-15-2022, 09:20 PM
|
#9 | ||||||
|
nope was just wondering if they would fit...nay look for some 2 frame 12 ga barrels to fit my d grade 10 ga 2 frame my 10 ga barrels have been cut to 26 inch and are pitted very bad...I have shot it with low power loads..just some wishful thinking.....charlie
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-16-2022, 09:31 AM
|
#10 | ||||||
|
One of my 1/2 frame 12 gauge guns are fitted with a set of 16 gauge barrels and fit pretty well. This DHE 1/2 frame gun was purchased without barrels and later fitted with a set of 12 and 16 gauge barrels from my junk pile. It is a real stunner with a stock smaller than any 28 or .410 stock I have ever seen.
|
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
