My First Parker

Allen Gill · 06-21-2018, 08:05 PM

The Cabela's description stated it had 26 inch barrels and a Pachmayr Decelerator Butt Pad, which I would assume is a replacement. They measured the chokes as .723 inch right and .713 left. The LOP 14 1/4, 2 3/4 DAH, and 1 5/8 DAC.

I was just curious and picked it up to see how it fit along with a couple other Patrkers of higher grade and this one fit while the other two did not. I went back a couple days later and it has found a new home after sitting in Cabela's for a couple of years.

P1010005.JPG

P1010009.JPG

P1010014.JPG

P1010011.JPG

P1010007.JPG

P1010008.JPG
P1010015.JPG

Mills · 06-21-2018, 08:17 PM

Welcome, Allen! Hope you enjoy your new Parker

Harry Collins · 06-21-2018, 09:49 PM

Allen,

You may find when you measure the bores that they might be more than the standard .729. Many Parker’s of the vintage of yours had .734+ bores. Your constriction might be .006 more than you think. You have a beautiful and useable Parker.
Kindest,
Harry

Allen Gill · 06-23-2018, 04:29 PM

Quote:

Originally Posted by Harry Collins

Allen,

You may find when you measure the bores that they might be more than the standard .729. Many Parker’s of the vintage of yours had .734+ bores. Your constriction might be .006 more than you think. You have a beautiful and useable Parker.
Kindest,
Harry

Harry,

You got me wondering. I was getting different readings depending how I held calipers. So, I borrowed some Meyers gage pins and I measured the right to be .723 and the left to be .715 inches.

I found a picture of a table online that shows .723 to be somewhere between imp. cyl. and skeet. The .715 is showing as light mod.

I think that will do fine for grouse and woodcock. It does pretty good on skeet and trap. A good shooter could show her off, but that's

not me.

Tom Flanigan · 06-25-2018, 10:15 AM

Allen...that is one great unmolested Parker. Congratulations. A great way to begin owning Parkers or a wonderful only one Parker if you choose.

Allen Gill · 06-25-2018, 12:22 PM

Quote:

Originally Posted by Tom Flanigan

Allen...that is one great unmolested Parker. Congratulations. A great way to begin owning Parkers or a wonderful only one Parker if you choose.

Hi Tom, It is a really nice to shoot and is becoming my favorite. Is the recoil pad a later add on? I would think so and the stock was probably reworked some at that time. What do you think? Allen

Mills · 06-25-2018, 12:28 PM

The recoil pad is probably added, but I would not worry about it. You should order a PGCA research letter, if you haven't already

Allen Gill · 06-25-2018, 12:30 PM

Quote:

Originally Posted by Mills Morrison

The recoil pad is probably added, but I would not worry about it. You should order a PGCA research letter, if you haven't already

Thanks Mills. I have not order the research letter, but intend to do so. Allen

Tom Flanigan · 06-25-2018, 03:40 PM

The Pachmayr Decelerator Butt Pad is certainly not factory issue. But is does not look out of place. For my own guns, I always remove the recoil pad and fit a Parker replicated butt plate that can be obtained from a couple of different vendors. The only guns that I personally want to see a recoil pad on is a Parker Trap gun. Originally Parker did fit recoil pads if wanted but the originals are most likely perished and need to be replaced. For these guns I fit a Silvers Pad.

Tom Flanigan · 06-25-2018, 03:45 PM

Allen, as far as the stocks being refinished, I would have to see some closeup pictures to make a determination. But, the stock certainly looks factory issue from what I can see. Really nice gun. I'm glad you got it and hope you can shoot it for many long years. The gun is a keeper for sure.