|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
09-03-2022, 04:14 PM
|
#3 | ||||||
|
I think you’re right Bill.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
||||||
 |
 |
 |
| The Following 2 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
09-03-2022, 06:55 PM
|
#4 | ||||||
|
My Father's 1902 vintage 2-frame VH has bores of .728"/.729". My 1889 vintage GH has bores of .757" but it was back to the Brothers P. at some point as it has the 1910 bolt and bolt plate.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dave Noreen For Your Post: |
|
|
|
09-04-2022, 08:42 AM
|
#5 | ||||||
|
The larger bores were common in the mid 1890's and I don't know when the switch to nominal 12 gauge bores happened. I have a 1901 gun that has .729 bores.
|
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to Bill Murphy For Your Post: |
|
|
|
09-04-2022, 11:37 AM
|
#6 | |||||||
|
Quote:
I ask because I have what I hope is a "cream puff" GH Damascus on it's way to Texas. Very nice wood, nice barrels (outside), sharp engraving and a bit of case color left, overall a nice gun that's been in a family for many years. I have 3 big concerns.....barrels, barrels, and barrels. Numbers match but is not listed in the serialization book. I have agreed with the seller the deal swings on the barrels being good dimension, thickness and shootable condition to MY satisfaction. A session with measuring tools and borescope when it arrives for a verdict. Thanks All! |
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Keith Doty For Your Post: |
|
|
|
09-04-2022, 03:21 PM
|
#7 | ||||||
|
Austin Hogan published data on this a long time ago. As with most of his research (choke shapes, french polish, etc.) it was so informative that I copied it to my Parker files so that it survived to my posterity. I am attaching it. Bottom line is prior to s/n 70,000, 12 ga bores were commonly in the .755 range, while afterward they tended to conform to the .730 range. Enjoy
|
||||||
|
|
|
||||||
|
|
|
| The Following 6 Users Say Thank You to Mike Poindexter For Your Post: |
|
|
|
09-04-2022, 10:18 PM
|
#8 | ||||||
|
In the 1886 Chamberlin Cartridge Co. ammunition catalog they offered special cartridges for Parker Bros. guns with over-size wads.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
10-02-2022, 02:06 PM
|
#9 | ||||||
|
There is a section in TPS that states the "true bore" was adopted as a standard in March 1892 for 12 gauge. The similar change for 10 bore was stated to have changed a few monts later. The passage states that after that date, a 12 gauge with the oversized barrels would be stamped with an "O", presumably for old or oversized.
|
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Arthur Shaffer For Your Post: |
 |
|
|
Linear Mode
