|
07-09-2011, 10:37 PM | #3 | ||||||
|
your question is well took...thanks for the concern...the damage was at the top of the stock where it joins the reciever...i had the stock off so no wood or any thing down in guns mechanics...wood was free of oil so it glued back together well...i then put a coat of super glue on the inside of the stock head...should be stronger than ever now...i put it back together and ran 20 2 3/4 inch magnums through it...no cracking apperared looks ok so far.. they have a new super glue out that doesnt set up so fast and said was made for vibrations and poundings so i tried it seems to do the job only time will tell... charlie
|
||||||
07-10-2011, 05:52 PM | #4 | ||||||
|
I've not tried super glue on stocks. However, Acraglas has always worked for me on cracked stocks.
Harry |
||||||
07-10-2011, 08:03 PM | #5 | ||||||
|
will have to get me some acra glass...this project came up on a whim and i was in walmart and the super glue was about all they had...ive tried elmers and garilia glue on another project with no sucess...as ive been told the secret to good bonding is to make sure all the oil is out of the wood...i was lazy on my first project but will heed all the knowledge and advise given from now on...live and learn and i also shot the super glue stock some this evening still holding together.... charlie
|
||||||
07-10-2011, 08:49 PM | #6 | ||||||
|
Charlie, The super glue you want to use will be found in hobby shops that deal in remote control model airplanes. It comes in different viscosities. The super thin works great on fine cracks. brownell sells it too but you can get it locally with no shipping. You can imagine it has to be strong because these planes take a beating.
|
||||||
07-10-2011, 09:10 PM | #7 | ||||||
|
You also need to make sure the wood you are glueing is clean and free from imbedded oil to ensure the epoxy cures properly. If not you are wasting your time.
|
||||||
07-12-2011, 05:22 PM | #8 | ||||||
|
ed what you said is true i tried to glue a oily stosk 3 times and the glue want stick to good.. charlie
|
||||||
07-12-2011, 05:51 PM | #9 | ||||||
|
Charlie, to degrease that wood get EZOff oven cleaner and spray and rinse with COLD water until the brown stuff stops leaching out. Stand the wood to dry thoroughly before you reglue. An old tooth brush will help get the junk out during the cleaning. This takes all finish and dirt out of the wood, but it's the only way to make a repair like that.
|
||||||
07-13-2011, 09:48 AM | #10 | ||||||
|
I use super glue to re attach the small chips that sometimes come off around a receiver or tang when you take a gun apart that has not been apart in 80+ yrs. I try to do it immediately and generally use a blunted round toothpick to hold the chip in while the glue dries so that I can see if it's seating back in completely. I'll usually then take and exacto knife and relieve the edge of the chip just a smidgen to get it away from the metal. this works well. I've also glued quite a few shattered violin tops back together with super glue, none of which have ever failed since. It works very well for that. I don't do it on expensive violins... just older "fiddles" that my clients use mostly for square dancing and such. If the wood is clean, super glue works very well. It's good for filling cracks also. You first make dust with a file from wood like you are filling, force the dust into the cracks then drip low viscosity super glue onto the fill until it's soaked and let it dry and work it down. I use that method to fill in around pearl or silver inlaying on stringed instrument finger boards and fiddle tail pieces. Haven't ever found an alternate method that works better.
|
||||||
|
|