Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Restoration

Notices

Reply
Thread Tools Display Modes
Ultrasonic joy
Unread 05-03-2018, 09:44 PM   #1
Member
Bill Graham
Forum Associate

Member Info
 
Join Date: May 2016
Posts: 284
Thanks: 231
Thanked 204 Times in 61 Posts

Default Ultrasonic joy

The colors inside these 1887 locks are showing up, thanks to an ultrasonic bath. The weathered coin exterior is looking better as well. Gotta love the ultrasonic.
Attached Images
File Type: jpg 877EDBCD-33B6-44A6-A914-F3F4DD64044F.jpg (455.6 KB, 2 views)
File Type: jpg 15BB88A1-2819-4BD3-8189-0BA0A91A2EF3.jpg (555.0 KB, 1 views)
File Type: jpg 94791FD8-62C2-4339-89D7-F3848A027682.jpg (555.9 KB, 0 views)
Bill Graham is offline   Reply With Quote
Unread 05-03-2018, 10:37 PM   #2
Member
wayne goerres
Forum Associate

Member Info
 
Join Date: Jul 2012
Posts: 2,096
Thanks: 2
Thanked 626 Times in 380 Posts

Default

Hope you don't mind a little unsolicited advice. You should consider removing the V springs before putting in an ultrasonic cleaner. One of these days your going to get a nasty surprise.
wayne goerres is offline   Reply With Quote
The Following 3 Users Say Thank You to wayne goerres For Your Post:
Unread 05-04-2018, 01:52 PM   #3
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,368
Thanks: 3,180
Thanked 12,348 Times in 3,300 Posts

Default

I was thinking the same thing, Wayne.
edgarspencer is offline   Reply With Quote
Unread 05-04-2018, 01:56 PM   #4
Member
Bill Graham
Forum Associate

Member Info
 
Join Date: May 2016
Posts: 284
Thanks: 231
Thanked 204 Times in 61 Posts

Default

What kind of surprise? Not using much heat and not cycling for long.
Bill Graham is offline   Reply With Quote
Unread 05-04-2018, 03:42 PM   #5
Member
wayne goerres
Forum Associate

Member Info
 
Join Date: Jul 2012
Posts: 2,096
Thanks: 2
Thanked 626 Times in 380 Posts

Default

They brake for unknown reasons. There have been reports of several members on this forum with broken springs from using Ultrasonic cleaning. It might be best to just remove the springs.
wayne goerres is offline   Reply With Quote
Unread 05-04-2018, 03:52 PM   #6
Member
Bill Graham
Forum Associate

Member Info
 
Join Date: May 2016
Posts: 284
Thanks: 231
Thanked 204 Times in 61 Posts

Default

Thank you. I’ve done the same with several Smith’s and never had an issue. Better safe than sorry, now that I know the risk.
Bill Graham is offline   Reply With Quote
Unread 05-04-2018, 03:59 PM   #7
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,787
Thanks: 504
Thanked 18,653 Times in 4,779 Posts

Default

I personally completely disassemble anything that goes into the ultrasonic. Small internal parts and springs go into a can of carb cleaner. And case colored parts go into the ultrasonic. I have not personally had Springs break in the ultrasonic, but I have heard of it happening. So I don't take the chance.

Plus, I want to make sure that no moisture is trapped inside of things after taken out. If all is broken down, all can be dried off and well oiled before re-assembly.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
The Following 2 Users Say Thank You to Brian Dudley For Your Post:
Visit Brian Dudley's homepage!
Unread 05-04-2018, 04:13 PM   #8
Member
Bill Graham
Forum Associate

Member Info
 
Join Date: May 2016
Posts: 284
Thanks: 231
Thanked 204 Times in 61 Posts

Default

After cleaning and drying, I ultrasic again but in a thin oil, let sit for a while, blow off excess before reassembly.
Bill Graham is offline   Reply With Quote
The Following User Says Thank You to Bill Graham For Your Post:
Unread 05-24-2018, 10:20 PM   #9
Member
Richard Flanders
PGCA Lifetime
Member
 
Richard Flanders's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 4,517
Thanks: 8,480
Thanked 5,538 Times in 1,717 Posts

Default

I use a small sonic cleaner intended for drafting pens to clean gun parts. I stand a pnut butter jar in it that contains lacquer thinner then pour water around the jar to fill the cleaner tub. The thinner removes goop that takes forever for other cleaners to remove, especially if you let them soak for a day before turning the cleaner on. The jar is big enough to put a Parker action in and when I'm done I can put the lid on and store it. For a few small parts I use Dawn dish soap solution in the cleaner without the jar. There are generally surplussed larger sonic cleaners, big enough to hold a disassembled Colt 1911 and more available on Ebay for very reasonable prices compared to a new one. Some will hold 2-3 Colts at once.
Richard Flanders is offline   Reply With Quote
Unread 05-24-2018, 11:27 PM   #10
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,073
Thanks: 36,785
Thanked 34,221 Times in 12,647 Posts

Default

The springs when compressed are under under stress and the molecules are in high tension. The ultrasound waves excite the molecules and can cause fractures. (from a layman in layman's terms.)





.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following 3 Users Say Thank You to Dean Romig For Your Post:
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:39 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.