Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Parker Hardware Question
Unread 10-21-2009, 05:22 PM   #1
Member
Rod N. Gunn
Forum Associate
 
Dave Fuller's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 429
Thanks: 117
Thanked 169 Times in 62 Posts

Default Parker Hardware Question

I just finished making a new Gun Room item, the ammo storage trunk shown below. I've been looking for a padlock and keep wondering if Parker's hardware business ever made such a thing? Anyone ever seen one?
Attached Images
File Type: jpg _MG_8587.jpg (53.2 KB, 16 views)
File Type: jpg _MG_8602.jpg (63.6 KB, 15 views)
Dave Fuller is offline   Reply With Quote
Unread 10-21-2009, 05:24 PM   #2
Member
Autumn Daze
PGCA Lifetime
Member
 
Dave Suponski's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,888
Thanks: 4,375
Thanked 4,048 Times in 1,727 Posts

Default

Dave,That is one sexy looking ammo locker.Nice Job! Yes Parker did in fact make padlocks.They pop up on Ebay from time to time.Sorry I dont have one right now or I would let ya have it.
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker
Dave Suponski is offline   Reply With Quote
Unread 10-21-2009, 05:57 PM   #3
Member
MarketHunter
PGCA Member
 
Destry L. Hoffard's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,160
Thanks: 599
Thanked 4,045 Times in 1,173 Posts

Default

I've seen a couple over the years, but never with a key. I wonder if a good locksmith could get one working?

DLH
__________________
I was as virtuously given as a gentleman need to be; virtuous enough; swore little; diced not above seven times a week; went to a bawdy-house once in a quarter--of an hour; paid money that I borrowed, three of four times; lived well and in good compass: and now I live out of all order, out of all compass. Falstaff - Henry IV
Destry L. Hoffard is offline   Reply With Quote
Unread 10-21-2009, 05:57 PM   #4
Member
winplumber
PGCA Member

Member Info
 
Join Date: Nov 2008
Posts: 1,632
Thanks: 1,761
Thanked 639 Times in 404 Posts

Default

A Winchester box with a Parker lock sounds like the best of both worlds. Nice box
Steve Huffman is offline   Reply With Quote
Unread 10-21-2009, 07:19 PM   #5
Member
Rod N. Gunn
Forum Associate
 
Dave Fuller's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 429
Thanks: 117
Thanked 169 Times in 62 Posts

Default

Thanks Guys... Hopefully some more Googling and eBay searching will turn one up. I just occurred to me that Vol 2 of TPS has a section on Parker Hardware I'll take a look at that too.
Dave Fuller is offline   Reply With Quote
Unread 10-21-2009, 07:38 PM   #6
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,628
Thanks: 6,190
Thanked 8,908 Times in 4,772 Posts

Default

I have not seen any evidence of a Parker lock, but I have seen Parker items that are not in the hardware catalogs, so, who knows.
Bill Murphy is offline   Reply With Quote
Unread 10-21-2009, 10:26 PM   #7
Member
Robert Delk
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 483
Thanks: 1
Thanked 121 Times in 85 Posts

Default

An acquaintance of mine has one of the largest collections of padlocks in the country. I"ll ask him as he has many rare and some unique padlocks,some of which he keeps in a bank vault.I have never heard of a Parker padlock in 40 years of collecting odd locks. They must be pretty rare if they exist. Keys can be made for most locks,altho' it can get expensive.
Robert Delk is offline   Reply With Quote
Unread 10-21-2009, 10:46 PM   #8
Member
Bindlestiff
PGCA Lifetime
Member
 
Robin Lewis's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,118
Thanks: 703
Thanked 2,925 Times in 870 Posts

Default

This lock thread has me surfing the net and I didn't find any lock information but I did find something of interest. Look at all the functions old Charlie was doing....

GUNS AND HARDWARE.--CHARLES PARKER.
charles parker commenced the manufacture of coffee-mills in 1832, in a factory 25 feet by 40, two stories high, with horse power. He now occupies sixteen different buildings, with dimensions as follows: No. 1, office and plating room, 18 feet by 45. No. 2, coffee-mill and burnishing shop with additions, 20 by 26, used as a store and varnish room; also addition for a coffee-mill shop, 15 by 25. No. 3, spectacle shop, 20 by 108. No. 4, tobacco-box shop and friction rollers. No. 5, coffee-mill shop, etc., 25 by 30, with addition, used as a store and varnish room. No. 6, vise shop, 25 by 160. No. 7, engine and boiler-room, 29 by 48. No. 8, finishing shop, 24 by 100. No. 9, store-house, 60 by 100. No. 10, screw shop, 30 by 200. No 11, foundry, 66 by 360, with additions. No. 12, blacksmith-shop, 16 by 20. No. 13, coal house, 20 by 20. No. 14, annealing shop, 20 by 20. No 15, coffee-mill shop, 30 by 45, with additions, 28 by 25, for oiling shop; also a japanning room, 10 by 15. No. 16, packing-room and carpenter-shop, 30 by 30. These buildings have been built from time to time as the busi*ness increased and demanded more room. The motive power is furnished by an 80 horse-power Corliss engine. Mr. Parker has, in connection with business here four other concerns controlled by him; one located two miles east of the city, one two miles west, one two miles south, and another half a mile west, where there are made iron spoons, ladles and forks, scales and hinges, machinery and guns, britannia spoons, and German silver spoons and forks; employing at these four concerns at different localities about three hundred persons, besides two hundred which are occupied in manufacturing coffee-mills, screws, spectacles, eye-glasses, tobacco-boxes, vises, butts, lanterns, match-safes, faucets, iron bench-screws, scis*sors and shears, cranks and rollers, barn-door hangers and rollers, gate and plain hinges, gridirons, bed-keys, wagon-jacks, scrapers, pulleys, lamp-hooks, window-springs, thumb-latches, hammers, gimlets, call and hand-bells, &c.

Probably there is no manufactory in the country that manufactures such a variety of goods as Mr. Parker. Among other inventions and improvements introduced to the public by Mr. Parker, is a breech-loading, double barreled shot-gun, which is the result of over two years of the most thorough experiments, and is claimed to be the best gun in use in this or any other country. The barrels are self-locked. The advantages claimed for his cartridge are, that it is a central-fire, coned, metallic cartridge, and is capped with the ordinary percussion caps. The weight of the gun is from 7 1-4 to 7 3-4 lbs. In connection is the United States Screw Company, incorporated in 1863, owned by Mr. Parker. The machinery for this branch of his business is all new and of the most approved kind.
Robin Lewis is offline   Reply With Quote
Unread 10-21-2009, 10:50 PM   #9
Member
Autumn Daze
PGCA Lifetime
Member
 
Dave Suponski's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,888
Thanks: 4,375
Thanked 4,048 Times in 1,727 Posts

Default

Guys..Check out TPS Volume 2 pages 889-892
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker
Dave Suponski is offline   Reply With Quote
Unread 10-21-2009, 11:28 PM   #10
Member
Rod N. Gunn
Forum Associate
 
Dave Fuller's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 429
Thanks: 117
Thanked 169 Times in 62 Posts

Default

Yep there it is... Not the most attractive lock ever but it would be great to find one. Plus, the key style might help if you needed to have a key made.
Dave Fuller is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:22 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.