Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Restoration

Notices

Reply
Thread Tools Display Modes
Barrels move horizontal when closed
Unread 10-20-2022, 10:27 AM   #1
Member
Eric Romanowski
PGCA Member

Member Info
 
Join Date: Mar 2021
Posts: 21
Thanks: 0
Thanked 13 Times in 8 Posts

Default Barrels move horizontal when closed

Hi
I have a 1909 GH 16ga with Damascus barrels and I’ve noticed that they have started to move slightly left to right or horizontal when the gun is closed. I’ve tried to research what’s causing this to happen but not having any luck. Any help would be greatly appreciated!
Eric
Eric Romanowski is offline   Reply With Quote
Unread 10-20-2022, 04:41 PM   #2
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,549
Thanks: 476
Thanked 17,415 Times in 4,593 Posts

Default

It is off face. Side to side movement is usually hook wear and also forend lug wear. Likely there is excessive bolt wear too.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
The Following 2 Users Say Thank You to Brian Dudley For Your Post:
Visit Brian Dudley's homepage!
Unread 10-20-2022, 06:07 PM   #3
Member
Eric Romanowski
PGCA Member

Member Info
 
Join Date: Mar 2021
Posts: 21
Thanks: 0
Thanked 13 Times in 8 Posts

Default

Thank you Brian I appreciate your knowledge!! I recently bought the gun and it fits me perfectly! I’m disappointed that I’m not going to use it this year with the season just starting! Looks like I’m going to have to find a good gunsmith to fix it and maybe next year I’ll be able to get it back into the woods!
Again thank you very much for responding!
Eric
Eric Romanowski is offline   Reply With Quote
Unread 10-20-2022, 07:00 PM   #4
Member
Austin J Hawthorne Jr.
PGCA Member

Member Info
 
Join Date: Aug 2009
Posts: 572
Thanks: 421
Thanked 384 Times in 198 Posts

Default

You could put a thin shim on the hook as a temporary fix for the bird season and then have it fixed correctly after that.
Austin J Hawthorne Jr. is offline   Reply With Quote
Unread 10-20-2022, 07:19 PM   #5
Member
Eric Romanowski
PGCA Member

Member Info
 
Join Date: Mar 2021
Posts: 21
Thanks: 0
Thanked 13 Times in 8 Posts

Default

That’s exactly what I did. Thank you Austin for your input it is appreciated!!
Eric Romanowski is offline   Reply With Quote
Unread 10-20-2022, 07:42 PM   #6
Member
Chris Robenalt
PGCA Member
 
Chris Robenalt's Avatar

Member Info
 
Join Date: Nov 2017
Posts: 603
Thanks: 1,628
Thanked 1,060 Times in 283 Posts

Default

Degrease and coat the hook with the yellow Satellite glue, then hit with Accelerater. I've done this on a gun or two, still holding and on face tight. A cheap fix.
Chris Robenalt is offline   Reply With Quote
Unread 10-20-2022, 08:20 PM   #7
Member
Eric Romanowski
PGCA Member

Member Info
 
Join Date: Mar 2021
Posts: 21
Thanks: 0
Thanked 13 Times in 8 Posts

Default

Thank you Chris!!
Eric Romanowski is offline   Reply With Quote
Unread 10-21-2022, 09:41 PM   #8
Member
Stan Hillis
PGCA Member

Member Info
 
Join Date: Oct 2015
Posts: 1,694
Thanks: 3,143
Thanked 3,898 Times in 1,112 Posts

Default

I came up with another way to do this, several years ago, on my BSS duck gun that I've shot off face. A BSS's hook cannot be welded because of the way they were made, but a shim from aluminum HVAC adhesive tape works perfectly, and lasts for about 300 rounds before needing replacing. The aluminum measures .003" and has peel off backing that exposes a really good adhesive. I just clean the hook good with alcohol and a cotton swab, cut a small square of tape with scissors, peel the backing off, put it in place, then carefully cut away the excess on the sides of the hook with an Exacto knife.

I know I should have the pin replaced and expertly put the gun back on face but it only gets used to shoot ducks and it'll outlast me the way I'm doing it. This winter I will most likely Loctite a piece of .003" steel shim stock in place.
Stan Hillis is offline   Reply With Quote
The Following User Says Thank You to Stan Hillis For Your Post:
Unread 10-22-2022, 06:52 AM   #9
Member
Eric Romanowski
PGCA Member

Member Info
 
Join Date: Mar 2021
Posts: 21
Thanks: 0
Thanked 13 Times in 8 Posts

Default

That was my first attempt but it was a little too thick I believe. When I went to close the gun the lever wouldn’t go back it stayed to the open position. I used two pieces of aluminum foil with some hing grease and it seems to be good. I’m heading out to pheasant hunt and I’ll see how it goes. I’m bringing some foil and grease with me just in case.
Thank you Stan for your time and response!
Eric Romanowski is offline   Reply With Quote
The Following User Says Thank You to Eric Romanowski For Your Post:
Unread 10-23-2022, 12:20 PM   #10
Member
tom tutwiler
Forum Associate
 
tom tutwiler's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 675
Thanks: 393
Thanked 743 Times in 223 Posts

Default

Just for a quick and super easy fix, one can degrease the hook with solvent and then cut and apply one of the free address labels all the charities seem to send you to make a donation. They are about .010 in thickness and since they are peel and stick, they are easy to trim and apply. I actually did it one time on a very loose Fox Pin gun just to try it out. Shot a round a clays and it held up fine.
tom tutwiler is offline   Reply With Quote
The Following User Says Thank You to tom tutwiler For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:22 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.