Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions General Discussions about Other Fine Doubles

Notices

Reply
Thread Tools Display Modes
Unread 01-07-2023, 09:16 PM   #11
Member
winplumber
PGCA Member

Member Info
 
Join Date: Nov 2008
Posts: 1,631
Thanks: 1,757
Thanked 634 Times in 403 Posts

Default

The gun was sold to a car dealer in or around Bowling Green Ohio the person who offered it to me has since passed away, was the gun marked anywhere as to Bowling Green Ohio
Steve Huffman is offline   Reply With Quote
The Following User Says Thank You to Steve Huffman For Your Post:
Unread 01-07-2023, 10:04 PM   #12
Member
Brett Trimble
PGCA Member

Member Info
 
Join Date: Apr 2020
Posts: 180
Thanks: 241
Thanked 336 Times in 78 Posts

Default

I didn’t see any markings to that effect. The gun shop owner in SD (who is a good guy) told me that an older gentlemen brought it to the shop ten or so years ago and that the shop owner bought it to use. He promptly put it in a safe and forgot about it. We were talking about vintage guns and he brought it out to show me..
Brett Trimble is offline   Reply With Quote
Unread 01-07-2023, 10:06 PM   #13
Member
Brett Trimble
PGCA Member

Member Info
 
Join Date: Apr 2020
Posts: 180
Thanks: 241
Thanked 336 Times in 78 Posts

Default

Mike, I would think of it as a nice shooter. It’s in good enough shape that I wouldn’t alter it other than to clean it up. So you think $7.5K but not higher?
Brett Trimble is offline   Reply With Quote
Unread 01-07-2023, 10:42 PM   #14
Member
ArtS
PGCA Member

Member Info
 
Join Date: Nov 2021
Posts: 770
Thanks: 56
Thanked 1,048 Times in 407 Posts

Default

I may be totally wrong, but it looks to me that pictures 6 and 7 show a small crack that starts at the right side of the wrist and runs diagonally back across the top of the wrist to a point halfway across the left side of the wrist. You can't see the whole thing in either picture due to the top lever, but it appears to line up through the small screw head in front of the safety slide.


Edit:

I just re-read winplumbers post and I believe that is the same crack I am talking about. In looking at the other pictures, it appears that there may be a couple of smaller cracks toward the rear of the right lock plate.
Arthur Shaffer is offline   Reply With Quote
The Following 3 Users Say Thank You to Arthur Shaffer For Your Post:
Unread 01-07-2023, 10:45 PM   #15
Member
Brett Trimble
PGCA Member

Member Info
 
Join Date: Apr 2020
Posts: 180
Thanks: 241
Thanked 336 Times in 78 Posts

Default

Art,

I think I’m seeing cracks on both sides. I’m going to take another look at the gun in person. If it is cracked, he’ll be able to make it right. Would change the value some, however..
Brett Trimble is offline   Reply With Quote
Unread 01-07-2023, 11:02 PM   #16
Member
Mike Poindexter
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 518
Thanks: 570
Thanked 632 Times in 246 Posts

Default

Brett, its just me and the gun doesnt really sing to me, so don't rely on my thoughts as a valid measure of the gun's value. I just passed on a pre-1913 Grade 2 LCS 16 ga FW in 98% condition because the guy wanted $6200 for it. To a collector, it might have been worth that. Not for me. As for shooters, nice A grade Foxes and G grade Parkers are what I search for, just enough engraving to make it nice to look at, but not so much that I stare at the gun instead of the bird. Again, that's just me, so take it with a grain of salt. Good luck.
Mike Poindexter is offline   Reply With Quote
The Following 3 Users Say Thank You to Mike Poindexter For Your Post:
Unread 01-07-2023, 11:09 PM   #17
Member
Brett Trimble
PGCA Member

Member Info
 
Join Date: Apr 2020
Posts: 180
Thanks: 241
Thanked 336 Times in 78 Posts

Default

Mike,

I completely understand your logic. In fact I’ve been looking for a Parker G grade in 16ga with shootable stock dimensions in good condition for quite a while. So far I’ve come up empty!
Brett Trimble is offline   Reply With Quote
Unread 01-08-2023, 04:59 AM   #18
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,535
Thanks: 2,948
Thanked 10,389 Times in 1,645 Posts

Default

Just my two cents. A 12ga CE in the condition shown would be a $5500. gun in my opinion, add in the small bore premium of 75% and I get to $9625. Very hard to come across a 16ga CE Lefever, good luck. Craig
Craig Larter is online now   Reply With Quote
Lefever C grade 16 ga EJECTOR gun
Unread 01-08-2023, 09:29 AM   #19
Member
Larry the Gun Guy
PGCA Member
 
Larry Stauch's Avatar

Member Info
 
Join Date: Feb 2011
Posts: 857
Thanks: 2,910
Thanked 1,554 Times in 380 Posts

Default Lefever C grade 16 ga EJECTOR gun

I don't think I would quibble over some of the most minor issues this gun has. A good wood guy, like a few on this forum, can fix those minor cracks. You may never see another one of those for SEVERAL years, if ever. If I were standing there, it would be my gun. And ultimately if you don't want it please PM me.
Larry Stauch is offline   Reply With Quote
The Following User Says Thank You to Larry Stauch For Your Post:
Unread 01-08-2023, 09:45 AM   #20
Member
Steiner
PGCA Lifetime
Member

Member Info
 
Join Date: Oct 2021
Posts: 753
Thanks: 5,921
Thanked 2,060 Times in 466 Posts

Default

I think that car dealer may be a friend of mine.
Dan Steingraber is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:26 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.