Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
Thread Tools Display Modes
Lead shot hanging up in the tube
Unread 05-15-2023, 05:42 PM   #1
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 3,745
Thanks: 7,186
Thanked 2,696 Times in 1,234 Posts

Default Lead shot hanging up in the tube

I am loading 410 ga shotshells in a new MEC 600 jr Sizemaster reloader. At the moment I'm loading 7 1/2 shot but its not all dropping down the tube when reloading. For some reason the 7 1/2 shot is hanging up in the tube. Is there a fix for this or do I need to just reload smaller shot sizes like #8 or #9 shot?

Please advise
A
allen newell is offline   Reply With Quote
The Following User Says Thank You to allen newell For Your Post:
Unread 05-15-2023, 05:54 PM   #2
Member
Wild Skies
PGCA Member
 
Greg Baehman's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,236
Thanks: 1,142
Thanked 3,603 Times in 984 Posts

Default

Shot bridging on a MEC is not unique, it can happen with any manufacturer’s machine.

There is only ONE fairly certain way of loading larger shot, (7-1/2), in a .410 machine that works with any consistency.

1) Polish the inside of the drop tube.
2) Make sure your shot is well graphite'd. Add graphite to the shot if necessary, before attempting to load it. Make sure the shot is well coated, but don't over-do it.
3) Raise the drop tube to approx. 1/2 inch below the mouth of the hull, when dropping the shot. (This is an important step).

Do these things and you will have fairly consistent success.
__________________
Wild Skies
Since 1951
Greg Baehman is online now   Reply With Quote
The Following 2 Users Say Thank You to Greg Baehman For Your Post:
Unread 05-15-2023, 06:16 PM   #3
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 3,745
Thanks: 7,186
Thanked 2,696 Times in 1,234 Posts

Default

Thanks Greg, Ill try them
allen newell is offline   Reply With Quote
Unread 05-15-2023, 07:26 PM   #4
Member
Woodcock survey
PGCA Member
 
Daniel Carter's Avatar

Member Info
 
Join Date: Apr 2015
Posts: 964
Thanks: 1,294
Thanked 1,389 Times in 595 Posts

Default

Allen i have found Greg's # 3 to be very important. I had the same problem with #9 and found that by giving it room to drop free from the tube that cured it.
Daniel Carter is offline   Reply With Quote
Unread 05-15-2023, 09:13 PM   #5
Member
Ken
PGCA Member

Member Info
 
Join Date: Dec 2015
Posts: 56
Thanks: 54
Thanked 46 Times in 29 Posts

Default

I stick with 9's in the loader and load shot with a dipper for larger shot. a lap full of shot is frustrating!
Ken Burgess is offline   Reply With Quote
Unread 05-15-2023, 09:16 PM   #6
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 3,745
Thanks: 7,186
Thanked 2,696 Times in 1,234 Posts

Default

You got that right Ken.
I called MEC and spoke with one of their customer service reps. He recommended Greg's #3. I tried it and it works.
allen newell is offline   Reply With Quote
Unread 05-16-2023, 08:53 AM   #7
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,059
Thanks: 2,905
Thanked 11,409 Times in 3,075 Posts

Default

The solution to the problem was given in Frank Srebro's recent post about shot bridging in his 9000 press. The nose of the ram tube is rolled in, to prevent the wad from being pulled back up. Rolling the end of the tube means the inside is also rolled in, (picture a choke) and the shot will bridge at that point. Reaming the inside of the tube eliminates the 'choke' and after that, it makes no difference how high up the tube is when you drop the shot.
edgarspencer is offline   Reply With Quote
The Following 5 Users Say Thank You to edgarspencer For Your Post:
Unread 05-16-2023, 09:00 AM   #8
Member
Randy Roberts
PGCA Lifetime
Member
 
Randy G Roberts's Avatar

Member Info
 
Join Date: Apr 2017
Posts: 2,886
Thanks: 4,415
Thanked 5,606 Times in 1,842 Posts

Default

Quote:
Originally Posted by edgarspencer View Post
The solution to the problem was given in Frank Srebro's recent post about shot bridging in his 9000 press. The nose of the ram tube is rolled in, to prevent the wad from being pulled back up. Rolling the end of the tube means the inside is also rolled in, (picture a choke) and the shot will bridge at that point. Reaming the inside of the tube eliminates the 'choke' and after that, it makes no difference how high up the tube is when you drop the shot.
Link below to the thread that Edgar refers to in which Frank solved the issue.

https://parkerguns.org/forums/showth...light=bridging
Randy G Roberts is online now   Reply With Quote
The Following 3 Users Say Thank You to Randy G Roberts For Your Post:
Unread 05-17-2023, 06:27 PM   #9
Member
Wild Skies
PGCA Member
 
Greg Baehman's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,236
Thanks: 1,142
Thanked 3,603 Times in 984 Posts

Default

Quote:
Originally Posted by edgarspencer View Post
The solution to the problem was given in Frank Srebro's recent post about shot bridging in his 9000 press. The nose of the ram tube is rolled in, to prevent the wad from being pulled back up. Rolling the end of the tube means the inside is also rolled in, (picture a choke) and the shot will bridge at that point. Reaming the inside of the tube eliminates the 'choke' and after that, it makes no difference how high up the tube is when you drop the shot.
Should we really be comparing Allen's issue of shot bridging with his .410 MEC 600Jr. dropping #7 1/2 shot vs. Frank's 28ga. MEC 9000 dropping #8 shot?

I've been reloading both .410 and 28ga. shells for over four decades on P-W 375 machines, both ram/drop tubes are as they came from the factory, straight and without the noses being rolled over. I can tell you that shot bridging is a whole lot more common occurrence with the .410 than with the 28 -- especially with the larger shot size...maybe your experience differs from mine.
__________________
Wild Skies
Since 1951
Greg Baehman is online now   Reply With Quote
Unread 05-17-2023, 07:33 PM   #10
Member
nid-28
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 561
Thanks: 30
Thanked 508 Times in 185 Posts

Default

While it slows you down a little bit, I raise the handle slightly and tap the drop tube with a screwdriver. That’s been very successful in limiting the problem of bridging.
Bill Davis is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:12 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.