|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
04-06-2023, 09:42 AM
|
#3 | ||||||
|
Scott Smith, a member here, often offers them for sale here.
Bob Jurewicz |
||||||
|
|
||||||
 |
 |
 |
| The Following 3 Users Say Thank You to Bob Jurewicz For Your Post: |
|
|
|
04-06-2023, 12:19 PM
|
#4 | ||||||
|
Brownell's or NEGC sells the mastodon ivory beads; I've used them and they work very well. As Dean said they can be stained to darken, and if they're too large I have chucked them in my Dremel and run them against fine sandpaper. They come with a shaft that may have to be cut down and trimmed a bit to fit the hole; I secure them with a drop of epoxy. Here's one on my Parker SBT; I didn't darken it because the original mid-bead was still quite white and I wanted them to match.
__________________
It ain't what you don't know that gets you into trouble. It's what you know for sure that just ain't so. - Mark Twain. |
||||||
|
|
|
||||||
|
|
|
| The Following 7 Users Say Thank You to Phil Yearout For Your Post: |
|
|
|
04-06-2023, 08:39 PM
|
#5 | ||||||
|
Question- if you epoxy in and need to remove in the future- what’s the procedure? Thx
Also looking for a replacement ivory front bead. Is there a vendor at the southern?
__________________
A Dog, A Gun, and Time enough! George Bird Evans |
||||||
|
|
|
||||||
|
|
|
|
|
|
04-07-2023, 08:15 AM
|
#6 | ||||||
|
Better to use purple or blue Loctite.
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Chuck Bishop For Your Post: |
|
|
|
04-07-2023, 09:08 AM
|
#7 | ||||||
|
Epoxy removal usually requires heat. You don't want to apply heat to a soldered barrel.
|
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Mike Koneski For Your Post: |
|
|
|
04-07-2023, 09:24 AM
|
#8 | ||||||
|
Concentrated heat like that from a hair dryer should be enough to soften epoxy enough to remove the bead without it being hot enough to melt solder.
50/50 solder requires 361F to melt. Your standard heat gun won't get that hot. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
04-07-2023, 12:11 PM
|
#9 | |||||||
|
Quote:
|
|||||||
|
|
|
|||||||
|
|
|
| The Following 4 Users Say Thank You to chris dawe For Your Post: |
|
|
|
04-07-2023, 12:22 PM
|
#10 | |||||||
|
Quote:
If you have a old white ivory bead , please put one on my Parker and I’d buy a second one from you Please and thanks |
|||||||
|
|
|
|||||||
|
|
|
| The Following 2 Users Say Thank You to Richard Mason For Your Post: |
 |
|
|
Linear Mode
