|
12-20-2011, 08:26 AM | #33 | ||||||
|
Well I picked up a 600Jr. Mark V on Ebay. Pete actually turned me on to the auction. Thanks again!
Nice lightly used machine that included total of 3 charge bars and 8 powder bushings. Got is for $165 shipped. I am excited to get the chance to reload my first shells.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
12-20-2011, 09:21 AM | #34 | |||||||
|
Quote:
Here are some websites you should find useful: Alliant Reloading Data Center: http://www.alliantpowder.com/reloaders/index.aspx Hodgdon/Dupont Data Center: http://data.hodgdon.com/shotshell_load.asp MEC Bushing Chart: http://www.mecreloaders.com/document...shingChart.pdf Where to get MEC accessories and parts: http://www.mecreloaders.com/ |
|||||||
12-20-2011, 07:30 PM | #35 | ||||||
|
Yeah, I was hoping to spend less money too, but I don't think I did too bad considering the condition and all the extras.
__________________
B. Dudley |
||||||
12-20-2011, 07:41 PM | #36 | ||||||
|
You did fine Brian, as I mentioned in my PM when I saw the auction, the bars and bushings retail for $70 plus (with no shipping) and you have a 6 point crimper and spare wad fingers. You are ready to go in wide range of loads. Wait until you see first hand how 7/8 ounce 12ga loads smash clay pigeons and how easy they are on the gun and shoulder. Reloading is really the way to go to control both pressure and recoil in vintage doubles.
|
||||||
12-20-2011, 08:58 PM | #37 | ||||||
|
Brian,
You'll drive yourself crazy with the bushings and the different charge bars. Do yourself a favor and buy an adjustable charge bar and you will be able to dial in exactly what charges you want to throw. Buy yourself a good scale- you'll need that no matter what kind of bar you use. Mec's bushing chart is not that accurate and it's not meant to be. I'm kind of a fanatic- if the load calls for 16.7gr., I want to throw 16.7gr. Take you time getting started and enjoy the fruits of your labor. Good luck, and as Pete says you will just love the way a 7/8oz. load smashes targets but not your gun. You will wonder why you ever needed an 1 1/8oz. load to break targets with. Daryl |
||||||
12-20-2011, 09:08 PM | #38 | |||||||
|
Quote:
|
|||||||
The Following User Says Thank You to Pete Lester For Your Post: |
12-22-2011, 01:00 PM | #39 | ||||||
|
I wouldn't be without an adjustable bar- have them for my 12ga 600 and my 650 in 12,20, and 28ga. You can get exact powder charges and I like to dial in the shot so it just fills the wad which is usually a bit light. You'll use less shot, get just as good a pattern because of less shot deformation, and have lower pressures. Most guys at my club load 12ga at 7/8oz for clays. I'm between 7/8 and 3/4oz [ maybe 3/4oz when I run out of CB-4100 wads and start useing CB-0178 wads] and have no problem keeping up with the hot shots. I like the adj. bar because you don't have to take bottles off to change bushings or bars. JMHI - Paul
|
||||||
12-22-2011, 01:31 PM | #40 | ||||||
|
Daryl, because at my club we put in big orders we get reloading supplies for dealer cost [ Claybuster wads are $68/5000 ] and I've been useing the CB-4100 wad that is for 7/8 or 1oz of shot. I'm almost out and have 5000 of the CB-0178 wads and it's .060 higher in the cushion area than the 4100. Think I can try some 3/4oz loads and finally get a good crimp. In one of the shotgun magazines I read that Tim Woodhouse tried the 0178 wad with 3/4oz of shot and they worked great. Only problem was at skeet, the pattern was too tight and he had to use softer shot to open it up enough. He claimed he used skeet chokes at sporting clays and had plenty of choke. With only 3/4oz in the 12ga there is almost no shot deformation. This could be a fix for any of you guys with old SxSs with no choke - should give you about an IC. Still have a 1000 of the 4100s so it'll be a couple of weeks before I can try the 0178s. For a powder charge, I'll use what I do for 7/8oz and pick up some FPS. Let you know how it works out. Paul
|
||||||
|
|