Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Unread 06-25-2009, 12:12 AM   #21
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,057
Thanks: 36,753
Thanked 34,178 Times in 12,640 Posts

Default

OK let's try again.

There, finally!!

I believe the hickory rod was in the position shown here while any weight added to the stock was in a larger hole bored higher in the stock - above the two mid-point screws. I have seen several stocks with two plugs and the only one that could have lined up to continue through the wrist was the lower one as pictured here.
Attached Images
File Type: jpg 011.JPG (156.9 KB, 13 views)
Dean Romig is offline   Reply With Quote
Unread 06-25-2009, 09:54 AM   #22
Member
Double Play
PGCA Lifetime
Member
 
Larry Frey's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 1,304
Thanks: 936
Thanked 2,782 Times in 636 Posts

Default

Dean,
You are correct about the size difference between the hickory insert versus the diameter of the holes used to adjust the weight and balance of a gun. This photo shows two plugs in my 16 Bernard gun.
Attached Images
File Type: jpg DSCN0344.JPG (87.4 KB, 16 views)
Larry Frey is offline   Reply With Quote
Unread 06-25-2009, 10:22 AM   #23
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,057
Thanks: 36,753
Thanked 34,178 Times in 12,640 Posts

Default

Yours is a 1-Frame isn't it Larry? Mine is a 2-Frame and the difference in frame sizes/buttstocks probably accounts for the apparant difference in plugs/rods between yours and mine.
Dean Romig is offline   Reply With Quote
Unread 06-25-2009, 12:00 PM   #24
Member
Double Play
PGCA Lifetime
Member
 
Larry Frey's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 1,304
Thanks: 936
Thanked 2,782 Times in 636 Posts

Default

Yes mine gun is a one frame but I recall a couple of years ago we discussed this subject and someone measured the Hickory insert diameter and it was about an 1/8" smaller than the plugs on my gun. When you get home scale and post the diameter of the reinforcing rod and I will measure and post the size my plugs and we will see what the difference is.
Larry Frey is offline   Reply With Quote
Unread 06-25-2009, 12:17 PM   #25
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,057
Thanks: 36,753
Thanked 34,178 Times in 12,640 Posts

Default

Will do. I have another I'll look at too.
Dean Romig is offline   Reply With Quote
Unread 06-25-2009, 10:05 PM   #26
Member
Pa SxS
Research Chairman
PGCA Lifetime
Member
 
Chuck Bishop's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,916
Thanks: 1,231
Thanked 5,077 Times in 1,453 Posts

Default

If you check in the Parker Pages for Parkers Found, you will find my entry of a 1 1/2 frame PH with patent stamp S/N 206585. It has a 9/16 diameter rod.
Chuck Bishop is offline   Reply With Quote
Unread 06-25-2009, 10:14 PM   #27
Member
Double Play
PGCA Lifetime
Member
 
Larry Frey's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 1,304
Thanks: 936
Thanked 2,782 Times in 636 Posts

Default

The two plugs in the gun I pictured above measure 1" in diameter.
Larry Frey is offline   Reply With Quote
Unread 06-25-2009, 10:32 PM   #28
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,057
Thanks: 36,753
Thanked 34,178 Times in 12,640 Posts

Unhappy

It just came to me - My DH was among the vast tonnage that left Hausman's on that fateful day along with Larry's and Rich's and countless others who assigned the repair of these guns to the capable hands of Russ Bickel.

I'm sure someone will remind me of this thread when I get the DH back.

The others I thought I could inspect and post my findings on either didn't have the rod or plug or I simply couldn't make it out.
Dean Romig is offline   Reply With Quote
Unread 06-25-2009, 11:50 PM   #29
Member
MarketHunter
PGCA Member
 
Destry L. Hoffard's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,258
Thanks: 628
Thanked 4,271 Times in 1,209 Posts

Default

I talked to Russ the other day and got a report of his progress. You boys gave him some interesting stuff to work on apparently. He's so good it scares me, he just fixed a problem on my magnum 10 gauge that three other gunsmiths haven't been able to figure out.

DLH
__________________
I was as virtuously given as a gentleman need to be; virtuous enough; swore little; diced not above seven times a week; went to a bawdy-house once in a quarter--of an hour; paid money that I borrowed, three of four times; lived well and in good compass: and now I live out of all order, out of all compass. Falstaff - Henry IV
Destry L. Hoffard is offline   Reply With Quote
Unread 06-26-2009, 09:36 AM   #30
Member
Ed Blake
PGCA Member

Member Info
 
Join Date: Nov 2008
Posts: 1,300
Thanks: 774
Thanked 859 Times in 351 Posts

Default

You mean he fixed that "missing" problem? I'll have to send one of mine to him. Sorry Destry, couldn't help myself.
Ed Blake is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:19 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.