![]() |
![]() |
![]() |
||||||||||||||||||||||||||||||||||||||
Visit Paul Harm's homepage! | |
![]() |
![]() |
![]() |
#23 | ||||||
|
![]()
I loaded some of the 3/4 loads (clay buster 175 wad, 16.5 grams red dot, fed 209a primers and federal hulls) and finally braved some of this Midwest heat wave to try them out. What a nice load. Very soft on the shoulder and consitant down range hits out to 40 yards. Thanks for all the help
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to David Weber For Your Post: |
![]() |
![]() |
![]() |
#24 | ||||||
|
![]()
I loaded up and shot a bunch of the 3/4 oz shells using the claybuster wad, clay dot and chedite primers. WOW very nice and effective and the recoil is nothing. I shot these loads in both my Parkers and it is very kind on the old guns and this old shooter. Thanks all Craig
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#25 | ||||||
|
![]()
I don't see a Clay Buster 0175 12 gauge wad in Precision Reloading ?
They do however show a 0178 that is supposed to be their copy of the Winchester WAA12L wad .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#26 | ||||||
|
![]()
The claybuster 0175 wad is specific for a 3/4oz. load. I used to use the 0178 wad (or WW12L) for my 3/4oz. loads but the since the 0175 came out that's all I use. Took the recipe right off the claybuster sheet in the bag- 15.5gr. Clays, WW209 (I now use Cheddite primers) and either the old AA hulls or Rem. STS/Gun Club. What a wonderful load.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#27 | ||||||
|
![]()
I think I am gonna give that load a try....
![]()
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#28 | ||||||
|
![]() |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#29 | ||||||
|
![]()
Has anyone seen a published 3/4oz load using PB powder? I have a lot of PB on hand that I use for 7/8oz loads.
Dave |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#30 | ||||||
|
![]()
Dave;
Check out the Hodgdon website. They have plenty of 24g loads at low pressure and modest velocity. 3/4oz is 21g. I've played with a 13/16oz load which is 23g. Drop me a PM or call and I'll fill you in on what I've got. Daryl |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|