Very dark patina stock — what to do

[James L. Martin]

I also use Rig and Ballistol

[Craig Budgeon]

I use High-Pressure lube which is used on lathe dead centers. It adheres very well to metal, will withstand very high temperatures, and doesn't effect finishes. I wouldn't recommend its use on guns other than hinge pins. It can be found at industrial suppliers such as MSC and probably Amazon. You will probably avoid making mistakes you didn't want to make by following Dewey Vicknairs advice, however, I think he prefers custom work as opposed to restoration.

[Ron Scott]

Anyone else use Renaissance Wax on gun exterior metal?

[Mike Franzen]

I love Vicknair’s writing style. Very entertaining. I used Murphy’s Oil Soap one time based on a recommendation from this forum. It just made a mess and seemed to have removed some of the original finish. I’ll never go near that stuff again. Since then I’ve just left the stocks alone or had a professional like Chris Dawe or Brian Dudley do the work. But, I’ve heard a lot of good things about Timberluxe. I’m going to order a bottle and see what it can do for my 1878 hammer gun stock that previously got soaped.

[Ron Scott]

Originally Posted by Mike Franzen

I love Vicknair’s writing style. Very entertaining.

How about his analysis of American made shotguns? I would imagine pretty controversial in this group.

[B. Dudley]

Originally Posted by Ronald Scott

How about his analysis of American made shotguns? I would imagine pretty controversial in this group.

How so? There was not much negative said about Parkers. And his thoughts on the other makers are spot on. Especially Smiths and Win 21s.

[Ron Scott]

Originally Posted by Brian Dudley

How so? There was not much negative said about Parkers. And his thoughts on the other makers are spot on. Especially Smiths and Win 21s.

You are right. I just reread the section on American made doubles. I remembered it wrong. He rips L.C. Smiths and Winchester Model 21s apart more than he criticizes Parkers. The only small criticism of Parkers is: "From a design standpoint, I would never refer to one as "hellishly" complex but they certainly are needlessly complex. I wouldn't be surprised to find that the designer got paid by the part. The early guns used a complex, multi-piece linkage to translate the toplever motion to the single under bolt.
With all of the pivots and contact points in this linkage one would imagine that wear would "stack up" and result in much play in the mechanism. One would be correct."

[Stan Hillis]

Originally Posted by Ronald Scott

You are right. I just reread the section on American made doubles. I remembered it wrong. He rips L.C. Smiths and Winchester Model 21s apart more than he criticizes Parkers. The only small criticism of Parkers is: "From a design standpoint, I would never refer to one as "hellishly" complex but they certainly are needlessly complex. I wouldn't be surprised to find that the designer got paid by the part. The early guns used a complex, multi-piece linkage to translate the toplever motion to the single under bolt.
With all of the pivots and contact points in this linkage one would imagine that wear would "stack up" and result in much play in the mechanism. One would be correct."

Well, in the interest of "completeness" since we're quoting Dewey, he did have this to say as well ....

Originally Posted by Dewey Vicknair

It is in the ejector mechanism that I would use the "hellishly complex" description. An entire book/manual could be written about this mechanism. I'll spare you. A common problem with ejector Parkers is that even though the gun is tight on face, the joint will be loose when the gun is open. This is caused by the forend iron wearing the forend lug at the point where they come into contact. This area experiences accelerated wear due directly to the pressure of the ejector mainsprings.

And this, actually .......

Originally Posted by Dewey Vicknair

The cocking mechanism (and the need to house it) is the reason that small bore Parkers look out of proportion. Regardless of gauge, the action remains roughly constant in size (from the action flats on down), giving the smallbore guns a very disproportionate look.

SRH

[Dean Romig]

Originally Posted by Ronald Scott

How about his analysis of American made shotguns? I would imagine pretty controversial in this group.

It goes to show that everybody has an opinion and many opinions differ.





.

[Rick Riddell]

Murphy’s and automotive polish!