|
Notices |
Welcome to the new PGCA Forum! As well, since it
is new - please read the following:
This is a new forum - so you must REGISTER to this Forum before posting;
If you are not a PGCA Member, we do not allow posts selling, offering or brokering firearms and/or parts; and
You MUST REGISTER your REAL FIRST and LAST NAME as your login name.
To register:
Click here..................
If you are registered to the forum and keep getting logged
out: Please
Click Here...
Welcome & enjoy!
|
![](images/beige_noir//category_left.gif) |
Putting a CHE back on face with an oversized roll joint |
![](images/beige_noir//category_right.gif) |
04-06-2017, 12:52 PM
|
#1
|
Member
|
|
Member Info
|
Join Date: Aug 2011
Posts: 10,711
Thanks: 494
Thanked 18,293 Times in 4,717 Posts
|
|
Putting a CHE back on face with an oversized roll joint
Here is a process post on a job I just completed. As many of you may know, I have on hand oversized roll joints for Parker extractor and ejector guns. The installation of the proper sized joint allows for weld-free refitting of the breech.
This Rondel engraved CHE 12g. had been restored many years ago and is exceptional, however, the fit of the barrels was not 100%. The gun was tight, but it was off face quite a bit. About .005-.006" at the top. These photos show the condition of the gun when I received it. Note the fit of the dolls head rib extension which really shows the issue, as well as the daylight that is visible at the top of the breech. It was a pretty glaring issue that was the only wart on an otherwise beautiful gun.
Before 1.jpg
Before 2.jpg
Before 3.jpg
A new oversized roll joint was installed into the frame. The joint selected was a diameter of .550" which is approximately .012-.015" larger in diameter than most original used roll joints. This gave me the .005-.006" needed on the hook face to get the barrels back to being ready for refitting.
New Joint.JPG
The top and bottom sides of the hook were smoke fitted to the new joint. And then the breech face was smoke fitted to the frame until the barrels fully seated on the frame. Making the barrels seat fully then left some play in the bolt lockup, so a brand new bolt (also available through me) was fitted to tighten up the lockup.
After fitting.JPG
The back side of the forend loop also needed some very minor reworking to get the forend to seat tightly as a result of the barrel fitting. The new roll joint then needed to be case hardened for both functional and cosmetic purposes.
Colored joint 1.JPG
Colored joint 2.JPG
The end result is a gun that is back on face and as tight in every way as it was when the gun was new. The photos below show the assembled gun. Note the appearance of the rib extension fit in comparison to the before photos.
After 1.JPG
After 2.JPG
And to finish the job, the breech face was stripped as it would have been new.
Striped breech.JPG
__________________
B. Dudley
|
|
|
The Following 70 Users Say Thank You to Brian Dudley For Your Post:
|
Adam Steinquist, allen newell, Bill Jolliff, Bill Murphy, Bill Zachow, Bob Jurewicz, Bob Kimble, Bob Roberts, Brett Farley, Brett Hoop, bruce a lyons, Bruce Hering, Bruce P Bruner, Buddy Marson, Chris Travinski, Craig Larter, Daniel B Sweet, Daryl Corona, Dave Tatman, David Dwyer, David Lien, Eric Eis, Eric Estes, Frank Cronin, Garry L Gordon, Garth Gustafson, Gary Bodrato, George Davis, Greg Baehman, GunnerGrilli, Harry Collins, Harryreed, James L. Martin, james whittington, Jeff Christie, Jerry Harlow, Jim Wescott, John Albano, John Brazelton, John Cinkoske, John Truitt, keavin nelson, Keith Doty, Kirk Potter, Larry Stauch, Louis Caissie, Mark Landskov, matt koepnick, Michael Moffa, Mike Franzen, Mills Morrison, Paul D Narlesky, Paul Ehlers, Pete Lester, Ralph English, Richard Flanders, Rob Marshall, Robert Brooks, Robert Kolesar, scott kittredge, Stan Hillis, Stephen Hodges, Steve Huffman, todd allen, Tom Kidd, Tom Pellegrini, tom tutwiler, Wayne Owens, William Stewart, William Woods |
|
04-06-2017, 12:58 PM
|
#2
|
Member
|
|
Member Info
|
Join Date: Jul 2010
Posts: 7,866
Thanks: 1,704
Thanked 8,315 Times in 3,296 Posts
|
|
Beautiful
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
|
|
|
|