Short 10 and Red Dot.

[William Davis]

Same with me no change to the standard Mec Crimp set up. Even fresh trimmed hulls crimp fine with Mec's Plastic Pre Crimp. I do Skive the hulls, don't have to but the wad slides in easier if Skived. It's a quick job Balistic Products Hull Skiving tool chucked up in the lathe. Hold the hull on the spinning tool with a little twist of the fingers for a second or so all it takes.

By the way bought a big box of once fired Federal 10 G hulls on line. my opinion It's a lot better Hull than Cheddites.

William

[Austin J Hawthorne Jr.]

I've been finding red dot a little difficult to come across lately. If anyone else does, they might try 21 gr. of 700X and 1 1/8 oz. of shot. This is another untested load, but I've been using it for years, and never had a problem with it in any of my 10's. Just an FYI, The IMR handloaders guide from 1996 lists 22.5 grains of 700X...SP10 wad...1 3/8 oz. shot...at 1190 fps. and 9700 psi., with a 2 7/8 inch case length.

[Paul Harm]

The super crimper is not necessary - on my cut shells I just use the standard Mec pre crimp toll and shells come out great.

[charlie cleveland]

i seen a box of winchester shells in 10 ga that were loaded with 1 3/8 ounce of lead shot the other day my first time to notice a older loading in this weight of shot shell...i can find reddot powder better in my area than i can the 700 powder...charlie

[Paul Harm]

Or Promo, the same as RD. Austin, I find it amazing that in 1996 IMR would be listing loads for the 2 7/8" 10ga. I would have thought that by 1996 the loads would just be for the 3 1/2" 10ga. I've used 700X but for targets - not sure but it was a 1 1/8 oz 12ga load they list. It's nice to see someone dig out a older reloading manual and find loads for the 2 7/8 10ga. Thanks.

[Austin J Hawthorne Jr.]

If I ever get around to it I'm going to shoot some of my 10 guage 2 7/8 Peters paper shells. Once I have the empties I'll work up a 1 1/4 oz load of #4 shot with 700 X and roll crimp it. Should be good for woodcock.

[10 bore]

Originally Posted by Austin J Hawthorne Jr.

If I ever get around to it I'm going to shoot some of my 10 guage 2 7/8 Peters paper shells. Once I have the empties I'll work up a 1 1/4 oz load of #4 shot with 700 X and roll crimp it. Should be good for woodcock.

i have an old load from dupont with 21 grs 700-x and 1 1/4 oz at 1175 fps. i shoot it at winter crows and it shoots good

[Mike of the Mountain]

Originally Posted by Austin J Hawthorne Jr.

If I ever get around to it I'm going to shoot some of my 10 guage 2 7/8 Peters paper shells. Once I have the empties I'll work up a 1 1/4 oz load of #4 shot with 700 X and roll crimp it. Should be good for woodcock.

You trying to vaporize those little ruddy fellows!!!!! I'd stoke those shells with #9 or #10 shot. That would be the ticket out of the 10g for Woodcock!!

[Austin J Hawthorne Jr.]

Have you tried that load in paper cases with wadding, or in plastic with SP 10 wads and a filler in the shot cup?

[Paul Harm]

Austin, I think your 1 1/4oz of #4's for woodcock is a little light - maybe a 1 3/8oz of BB's would be better.