Question on Chamber Length

[Austin W Hogan]

Dave; Parker Pages editorially advertised for a citation to verify that chambers were cut shorter than shells in Parker's era. Ed Muderlak found a 1933 article based on 1932 work that we scanned and reprinted. That article was written by a person with good industry credentials but covered only one gauge and shell length; 3 inch 410 in 2 1/2 chambers. The three inch shells produced better patterns in the 2 1/2 inch chambers, but the author noted an inch of case was burned away in the process.
We will put out the call again in the next issue, in search of such information printed in the pre 1929 era. We know that Parker Bros was a member of the industrial fore runner to SAAMI in the 1920's when they began stamping "overload proved" on barrels, but I have not been able to obtain a copy of those standards through SAAMI.
I have always considered those tables in the Remington Salesmen's Catalog to be a typo/transposition when I have my editorial hat off. The current SAAMI standard clearly calls for short shells in long chambers. After reading your post I measured a few modern barrels with the equipment I used to measure the Super Fox. My Rem 3200 labelled "Trap" measures 2 7/8 inches; my ca 1985 Ruger Red Label marked 3 inch measures 3 3/16 inches, and my 11 87 trap barrel measures about 3 inches.
I have seen some anecdotal accounts that M21's were short chambered in the 1930's but have no physical evidence to verify this.
I obtained my first hunting license in 1950. My hunter training instructor warned us that "low brass" shells were no longer shorter and lighter as they were in the time before WW2, and that if we were told by an elder that low brass was ok in old single shots and break open guns, we should have the individual guns examined before using "modern" ammunition. I became a hunter safety training instructor in 1964, and my NRA correspondence course contained the same warning and information.
I also note in Stadt, that Winchester changed the designation of the M1893 to M1897 when they adopted the 2 3/4 chamber. Stadt also notes that 2 3/4 inch shells were labelled "Repeater" on the box.
We (Parker Pages) and I would really like to clear this up. A copy of that 1920's industry standard would be a good arbitrator.

Best, Austin

[Bruce Day]

Austin, SAAMI ( Sporting Arms and Ammunition Manufacturer's Institute) is headquartered in Newton , CT . Although its usually difficult to get one of these minimally staffed trade organizations to conduct any file research for persons who are not members of the organization, perhaps they would allow access to a researcher. Current standards are available on line. Maybe we have a member who lives in Connecticut ?

[Pete Margiotta]

Hey Dave, good to hear from you. My Mahoney setter "Jussie" just turned 7 in march. He is still hunting strong. We had a good season for woodcock and grouse. still shooting my modified 20 gage fox sterlingworth, but i am looking forward to shooting the parker. Is you dog working out well for you? pete

[Autumn Daze]

Sorry Bruce,Nobody here in Connecticut that I know of....

[Bill Murphy]

Austin, I don't have the drawings and specs in front of me, but we have found several instances of Parker Brothers memos and drawings that specify chambers 1/8" shorter than the shells meant to be fired in those chambers. We have also seen Parker Brothers hang tags specifying "2 5/8 inch chambers for use with 2 3/4 inch shells." We have also seen Parker Brothers orders specifying the same thing. I believe I have articles from older American Rifleman magazines noting that this short chambering is somewhat of an industry standard, although not universal. These Parker Brothers standards continued into the Remington era. I think it would be very easy to confirm by examining stock book entries from the twenties that indicate that a gun has been built with 2 5/8" chambers and proved and patterned with 1 1/4 ounce shot loads.

[Austin W Hogan]

Bill; I would really like to find a solid pre 1920 reference to this long shell in short chamber pattern theory. I think Askins the elder alluded to it but did not verify or explain it.
The bore jig I used to measure the Super Fox allowed me to make some quantitative measurements about this. One of my own "competition" guns is 136683 that dates from 1906 and was made to measurements by DuBray. It shoots beautifully tight, round patterns with both barrels. It is chambered 2 3/4 inches; the front of the forcing cone has a long taper ending at the barrel diameter of .740 inch at 6 inches from the breech, and one choke is more parabolic than like Oscar's "OGEE". I have a VHE with btfe and monte carlo, no safety 170789 , 32 inches that shoots similar round patterns. It is also 2 3/4 chamber with the forcing cone taper meeting the bore of .738 at 5 inches from the breech, and again a more parabolic choke in the left (full) barrel. A third 32 inch PH (207489) also reaches .738 at five inches, and the left barrel choke begins at .740 five inches back from the muzzle with a more parabolic than ogee taper. These dimensions do not duplicate the Super Fox, but the forcing cone taper and choke taper is of the same form.
These three guns tell me either that these owners sent their guns to Becker, or that King knew how to produce these patterns with forcing cone and choke profiles that did not involve jamming the case mouth into the forcing cone.
I have some "new" primed 3 inch ten gauge paper cases from two makers that have never been loaded or fired. They measure 2 7/8 inches precisely. I would like to find some unloaded twelve ga cases to measure.
The Super Fox has beautifully tapered chokes and forcing cones. The chambers measure .788 - 792 at 2 5/8 from the breech. The most common plug type chamber gauges are .792 wide. I did not measure the Super Fox with a blade gauge, but it may have measured 2 5/8.
Multiply fired modern 2 3/4 cases measure 2.66 +/-. Squaring the ragged mouth would shorten them a little. Were paper 2 3/4 cases also 2 5/8? We need some unfired cases to measure.

Best, Austin

[10ga Hammer]

"Were paper 2 3/4 cases also 2 5/8? We need some unfired cases to measure."


Austin, I just took a quick look at some unfired paper hulls I have stashed away and found a 12ga paper Federal "Monarch" measures 2 5/8, a 10ga "Leader" 2 5/8, and a 16ga "New Rival" 2 9/16. HTH, Bob

[Bruce Day]

CHE 241,601 12ga is marked "For 2 3/4" shells". The chambers measure 2 5/8" to the beginning of the forcing cone.

[Researcher]

The Remington era specification sheets for their Parker guns are reproduced on pages 164 to 169 of The Parker Story and show the chambers 1/8 inch shorter then the intended shell. A.P. Curtis did a couple of articles in The American Rifleman (July 1936 and March 1938) on the virtue of short chambers.

Pete, my Mahoney girl is 7 1/2 and is at the height of her powers. She is a bird machine. Currently her daughter is pregnant and I'm first in line for a puppy.

[Bill Murphy]

The A.P. Curtis articles that Dave mentions are the articles that I alluded to earlier in this thread. The Remington specifications that Dave mentions were dated as late as February 20, 1940, so, obviously, Remington kept the short chamber specifications to the end of production. Notice the marking on late Remington guns says "For 2 3/4" Shells" with no mention of chamber length. The chambers for 28 gauge and .410 bore guns were 1/16" shorter than the shells intended to be used.