![]() |
![]() |
![]() |
||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
will send info on mould maker..may take a little while for me to find it..somebody here on the site gave it to me maybe they will remember it too and post it again... like i say this fellow makes a nice piece....charlie
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#4 | ||||||
|
![]()
the "not for ball" proof designates a choke or reduction in the bore size.
personally, i follow the advice. i would think that at minimum you should make sure the ball is a hair smaller the the smallest diameter in that bore. there should be marks for chamber and bore size. tight 10's often have a reduction to 12 bore in the tubes.
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
heh phil im still looking for the mans address that makes the mold its somewhere in my collection of things...dont give up hope... i hope some one pitches infor some one here gave me his address fore sure...i sure wish i could be more organized... charlie
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to charlie cleveland For Your Post: |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
No problem Charlie, I just got three boxes of shells loaded by Tom Armbrust. Some #2 and some #4. Should keep me in the Predator shooting business for awhile. I am going to start assembling some sort of loading equipment for the 8 gauge. I need to see if I can modify some 10 gauge magnum equipment.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#7 | ||||||
|
![]()
the old 10 ga lee hand loader is what i use and then i have a roll crimp for thecrimping but do wish i had a 6 way or 8 crimp also...you can pobably get the mans name from tom who makes the hull resizer...there is a 1 stage that does it is one operation and theres some folks who make it ina 2 stage operation...or you can get a pair of pipe crimping pliars and with 1 minute s use of a die grinder you canhave a hull resizer but my way takes about 30 secounds to resize a hull and it dont look as pretty as toms but it works fine for me...just reminded me i was supose to have sent wayne a picture of it ... hope you good luck with the predertor control with the 8 ga...these are stories we are waiting to hear... p s what kinda loads did you have tom load up 2 -3 ounce etc.... charlie
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | ||||||
|
![]()
I had some 2 1/2 and some 2 1/4 OZ loads done. Tomorrow morning is the day. Will be getting up around 4AM and start at day light. My 9:00 AM it is getting about 95 degrees and nothings moving. Not even a hungry coyote.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#9 | ||||||
|
![]()
Phil I hope you are keeping cool out there in tuscon with this record breaking heat. I try not even to go outside unless I have to.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#10 | ||||||
|
![]()
make sure not to forget gun or ammo and wind and set the old alarm clock maybe even put it under a dishpan...good hunting we ll be waiting for the storey... charlie
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|