![]() |
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
John, it may not be a simple job, most engraving is done before a gun is case hardened, I'm not sure you can engrave it now, it may have to be annealed (sp?) engraved and then case hardened again. I'm sure someone like Brian D (who knows) will jump in here and give the proper advice
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Eric Eis For Your Post: |
![]() |
![]() |
![]() |
#4 | ||||||
|
![]()
Noelle, is as Dean said and very pleasing to talk to. She did some screw work for me.
__________________
Father, will I be able to be brave when I am afraid? Child, that is the only time one can be brave. |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to calvin humburg For Your Post: |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
Cased gun parts are to hard to engrave and must be annealed and hand polished before any engraving,I was asked by a client to engrave his rifle receiver cutting through the bluing and I told him it's unprofessional and I would never do. J.J.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
I agree with Dean. Noelle has engraved a number of screws for me and also chased other engraving and she does a great job. Her number is 203-788-4828, noelleinct@yahoo.com. Her charges are also very reasonable. Check out her web page at www.engravingbyNoelle.com. Tom
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#7 | ||||||
|
![]()
I contacted Noelle this morning and I am going to send the gun out to her this evening.
Thanks guys!
__________________
"Everybody knows that the autumn landscape in the northwoods is the land, plus a red maple, plus a ruffed grouse. In terms of conventional physics, the grouse represents only a millionth of either the mass or the energy of an acre. Yet subtract the grouse and the whole thing is dead." - Aldo Leopold |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | |||||||
|
![]() Quote:
![]() Last edited by David Noble; 01-19-2017 at 05:00 PM.. Reason: clarification of time frame. |
|||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#9 | ||||||
|
![]()
Dave,Do you know who engraved your Colt Python and did you have any problem with any rust on the exposed engraving? J.J.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#10 | ||||||
|
![]()
I had no idea who engraved it but I feel my collector friend might have. There was no problem with rust during the six months that I owned it, and I have no idea how long it had been engraved before that.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|