|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
01-27-2026, 11:25 PM
|
#23 | ||||||
|
What do you need for barrels Harold?
I have a set of 0-frame Damascus ejector barrels cut from 28” to 26” that Breck refinished for me last year. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
||||||
 |
 |
 |
|
A few 16’s | |
|
01-27-2026, 11:25 PM
|
#24 | ||||||
|
A few 16’s
A pair of 16 Lifters (consecutive serial numbers) ordered by a gentleman who was an architect in the New England area.
The facts regarding these 2 16’s were discovered by a fellow member who then reached out to me and invited me to hunt with him, they are special Parkers. This great friend suggested we enter them in the 2025 People’s choice award in Sanford, they placed 3rd. PS.The lower 16 has been restocked to correct some of the mistakes of a former restock, as you will note in the last picture. |
||||||
|
|
||||||
|
|
|
| The Following 27 Users Say Thank You to Stan Hoover For Your Post: | Bill Jolliff, bob lyons, Brett Trimble, Brian Hornacek, Chris Pope, Clark McCombe, Craig Larter, Dan Steingraber, Daryl Corona, David Noble, Dean Romig, Don Ladd, Donald McQuade, edgarspencer, Garry L Gordon, GunnerGrilli, james whittington, Jerry Harlow, Josh Loewensteiner, keavin nelson, Ken Hill, Larry Stauch, Paul Ehlers, Rick Roemer, Wally Barrick, Wayne Owens, William Woods |
|
|
|
01-27-2026, 11:29 PM
|
#25 | ||||||
|
Stan, just superb.. like so many others in this thread. It’s 16ga “heck” around here!
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Brett Trimble For Your Post: |
|
|
|
01-28-2026, 07:54 AM
|
#26 | ||||||
|
Dean, the bores on that PH are rough. Measured them at Brett Hoops house, but need to have them looked at by John Hosford or someone else knowledgeable. The barrels on that gun are extractor, Twist steel, and were already cut to 26", can't remember the original length, if I ever knew it.
I have hunted /shot it with light low pressure loads. Ser # 64366
__________________
"How kind it is that most of us will never know when we have fired our last shot"--Nash Buckingham |
||||||
|
|
|
||||||
|
|
|
|
|
|
01-28-2026, 09:51 AM
|
#27 | ||||||
|
For looking at the little Rem era GHE 16 with 28" barrels is kinda pretty with its original A&F case.
As far as hammer guns go this little Quality U Top Action with 32" Twist barrels on a 1 frame is fun to shoot. The 2 frame 16 DH with 32" Titanic barrels would have to get the nod as my personal favorite though when it comes to shooting. |
||||||
|
|
|
||||||
|
|
|
| The Following 16 Users Say Thank You to Randy G Roberts For Your Post: |
|
Wood | |
|
01-28-2026, 10:02 AM
|
#28 | ||||||
|
Wood
That wood on that top action hammer gun is incredible!
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Larry Stauch For Your Post: |
|
|
|
01-28-2026, 10:07 AM
|
#29 | |||||||
|
Quote:
|
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Randy G Roberts For Your Post: |
|
|
|
01-28-2026, 10:31 AM
|
#30 | |||||||
|
Quote:
|
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Larry Stauch For Your Post: |
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
