Need advice and info on 28ga Repro mods

[Bill Murphy]

I am not sure of this, buy I think my friend Ken got his barrels back from Mr. Orlen untouched by a gunsmith's hand.

[Reproman]

Thanks everyone for the input and suggestions. I decided to go for it because if I could have a "dream" two barrel set it would be 26" Q1 & Q2 and 28" IC & M. I dropped them off with Bill Schwarz last week.

One more question though: If all Repro's have chromed lined barrels, does that pose a problem when the chokes are opened up?

[Autumn Daze]

Marvin,Industrial chrome plating takes about an hour in the tank to coat to a depth of .001. So I would think that whatever you do to the chokes would remove all traces of chrome in the reworked area.

[Sowega 01]

Marvin,

I have used Bill Schwarz since 1988 and he has rechoked steel and damascus Parkers for me. I am well satisfied with his work.

Asa Kelley

[SXS OHIO]

Asa...how does he re-choke barrels with no or little choke? Kenny

[Sowega 01]

Kenny,

I used the wrong term. Bill has only opened chokes for me. Most all of the barrels I sent him were very tightly choked.

Asa

[Chuck Heald]

Two questions;

what is it about flush screwin chokes that everyone loves to hate? They are all but invisible and provide a flexibility.

What's this about chrome lined bores in the Repro?

[Joe Bernfeld]

Originally Posted by Chuck Heald

Two questions;

what is it about flush screwin chokes that everyone loves to hate? They are all but invisible and provide a flexibility.

What's this about chrome lined bores in the Repro?

As Dean said all Parker Reproductions had chrome lined bores, and all were recommended for steel shot in chokes of modified or looser. However, they did not chrome line the choke area, in order to make it easier to open the chokes if desired. And by the way Chuck, thin wall choke tubes are great. I have a set in a Lebeau Courally. However, the Parker Repro barrels are not real thick, so it might not be possible to have them installed. The SCC model with internal screw chokes has thicker barrel walls at the muzzle.
Joe

[Setter Man]

Just dropped off my 28 ga Repro at Brad Bachelder's to have the receiver re-case colored. I also took with me both sets of barrels. The 28" barrels, marked M/F were choked .034/.012 and the 26" barrels marked Q1/Q2 were choked .014/.014. Me thinkst the 28" set had already been opened.

By the way: Brad showed me a 20 ga Repro frame they just finished refinishing. It looked very nice - similar to the $49k 28 ga Parkers Tony is/was making. Note: this is not an excuse to start critiquing re-case color jobs and who does/does not do a good job. I am just saying the job he did on that 20 ga was very pleasant to the eye and much better than the sprayed on crap the gun came with.

[Wild Skies]

Originally Posted by Jay Gardner

Just dropped off my 28 ga Repro at Brad Bachelder's to have the receiver re-case colored. I also took with me both sets of barrels. The 28" barrels, marked M/F were choked .034/.012 and the 26" barrels marked Q1/Q2 were choked .014/.014. Me thinkst the 28" set had already been opened.

Gosh Jay, those Q1/Q2 chokes at .014/.014 are odd balls--you ought to have Bachelder's mike them again to verify. My 28-ga. 26" Q1/Q2 set measures .004/.008, the 28" M/F set measures .014/.034...these are known to be the original unaltered chokings as they came from the factory.