Steve's new GH

[Stepmac]

Originally Posted by Ed Blake

You did great. Nice gun. In regards to the chokes, leave them as they are and shoot it before you take that step. Then decide. There are some great published 7/8 oz. Low pressure loads. Easy on the gun and you

I'm going to have the chamber measured. You say "published 7/8 ounce loads". I assume you are alluding to loading my own. I guess, if it is short that I'll load Cheddite hulls. If the chambers are short, I'll shoot short shells. Do standard shotshell manuals quote low psi loads?

[StubTwist]

Originally Posted by Steve McCarty

Do standard shotshell manuals quote low psi loads?

You can check online from the powder manufacturer.

http://www.hodgdon.com/basic-manual-inquiry.html

My target load is: Remington STS hull; Remington 209 primer; Claybuster 1100 wad; 23 grains of IMR 7625; 1 oz of shot. 5100PSI 1150 fps velocity.

[SXS OHIO]

Shoot that gun as it is and check your patterns....cutting the chokes open is a one way road and must be properly performed or the new patterns could be off point of aim or just not what you wanted....Spredders are great for 12 bore guns and will not change the guns P.O.A. And if you want to go out west and hunt wild roosters it will make a great gun for that too....(-: SXS ohio

[Stepmac]

Originally Posted by Kenny Graft

Shoot that gun as it is and check your patterns....cutting the chokes open is a one way road and must be properly performed or the new patterns could be off point of aim or just not what you wanted....Spredders are great for 12 bore guns and will not change the guns P.O.A. And if you want to go out west and hunt wild roosters it will make a great gun for that too....(-: SXS ohio

Thanks, Kenny: I've been reading about spredder shells. I'd rather not mess with the chokes. The gun is in very nice condition. Most of the barrels show black damascus figuring. Where the original owner's fingers wrapped around the barrel at the forearm the tubes are worn silver.

I'm toying with the idea of having the barrels re-finished, just because I love the look of the dark damascus figuring. Keith Kearcher lives just down the road from me and has done lots of work for me in the past. He is very good.

The GH is pretty heavy. It is almost very heavy when compared to my Lefever and it seems heavier when compared to my Sterlingworth. However the gun balances well. The tubes are 30 inchers, but for some unknown reason they don't seem long.

The barrels seem thick at the breech. Seems to me that it'd be hard to blow them up, but I've read what we have all read, and I'm going to be careful.

Someone here said I should load 7/8 ounce loads. Sounds like a good idea to me. Then it'd shoot about like a lightly loaded 20 gauge. That's okay with me.

I have to admit that the thought of shooting a damascus Parker is intriguing to me.

"What ya shoot'en?"

"A Parker."

"Oh."

Okay, I'm a snob.

[Dean Romig]

What is the frame size? Presuming it is a 12 gauge it could be a 1-frame, a 2-frame or a 3-frame. I don't believe the 1 1/2-frame had been introduced at the time yours was made.

[Stepmac]

Originally Posted by Dean Romig

What is the frame size? Presuming it is a 12 gauge it could be a 1-frame, a 2-frame or a 3-frame. I don't believe the 1 1/2-frame had been introduced at the time yours was made.

Yep, it is a 12 and 2 frame. The gun is not light, but not nearly as heavy as a Superposed. I don't know how to weigh a gun. Step on the scales with the gun and then without and subtract the difference? I don't think bathroom scales are precise enough.

[Carl Erickson Jr]

Before you start working with spreader loads or changing chokes pattern your GH. You might have the patterns that you want already. I patterned my new GH on Friday and found that my right barrel was full and my left improved/modified. By the way,mine cost $200 at a gun show but it was not as nice looking as yours (it was ugly!) , It still shoots well!

[Stepmac]

Originally Posted by Carl Erickson Jr

Before you start working with spreader loads or changing chokes pattern your GH. You might have the patterns that you want already. I patterned my new GH on Friday and found that my right barrel was full and my left improved/modified. By the way,mine cost $200 at a gun show but it was not as nice looking as yours (it was ugly!) , It still shoots well!

I find that a "beater" can be brought back. Black wood can be lightened with proper technique. Rust is an issue. I never really scrub on rust since doing so shines the finish and looks like it has been scrubbed. So your gun may have a brown patina that will have to stay. But that's not all bad.

I fix cracks. Either I do it, or a gunsmith does, if they are difficult enough. They will spread the crack and fill it with glue.

A good gunsmith can make those barrels glow like absolutely new. It'll cost you about $300 to do it though. We have one of the best gunsmiths in the country here. All he does is re-furbish old guns. He uses nothing but authentic methods. Keith Kearcher. He has a website, so you can google him. While I'm not recommending it. You can give him a really beat up gun and say, "Make it new, Keith", and he will. It'll cost about a grand. He can do the engraving, the whole bit. (He sends it out for engraving.)

The only guns that I have had Keith refurbish were really in terrible shape. So terrible that they were junk. One a muzzle loading rifle and the other a muzzle loading shotgun. I didn't want the shotgun to look new, just nice and that's what he did. Now it is something to be pround of. The ancient rifle is absolutely wonderful. Doesn't look exactly new, but pretty.

What shells are you shooting?

[Bruce Day]

Nice gun. Undamaged by human hands.

That gun will handle about any reasonable load you want to shove through it , although you can elect to shoot lesser loads to keep it easy on you. A 1 oz or 7/8oz load makes a soft target load.

That gun configuration was the workhorse for most of the existence of Parker Bros.

Enjoy.

[Carl Erickson Jr]

Currently I am shooting 7/8 oz of 7.5 shot in my doubles. My 1889 barrels were nicely cold blued and I will probably want to have them restored. Thanks for the info about someone who can do that kind of work. While the bore is rough as the patterns are good I will leave the bores alone, At some time in the future will have the stock replaced as the wrist repair is not the best .