|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
02-04-2023, 12:12 PM
|
#3 | ||||||
|
If it's on a 0 frame, the barrel wall thickness will be good.
|
||||||
|
|
||||||
 |
 |
 |
| The Following 2 Users Say Thank You to Chuck Bishop For Your Post: |
|
|
|
02-04-2023, 12:19 PM
|
#4 | ||||||
|
I have a 00-frame 28 gauge made in 1935 that I shoot both 2 1/2" and 2 3/4" in but I've never measured the chamber length of it.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
02-04-2023, 12:41 PM
|
#5 | ||||||
|
Dean, I'd expect a 1935 vintage 28-gauge to have 2 13/16-inch chambers intended for 2 7/8-inch shells.
Remington Specification Sheet GHE 28-ga highlighted.jpg The progressive burning smokeless powder, high velocity, 3/4-ounce, 28-gauge loads were introduced in 1931. Super-X Loads, March 1, 1931.jpg NID 28-ga Field & Stream April 1932.jpg |
||||||
|
|
|
||||||
|
|
|
| The Following 9 Users Say Thank You to Dave Noreen For Your Post: |
|
|
|
02-04-2023, 01:06 PM
|
#6 | ||||||
|
You're exactly right Dave! I just went to my gun room and measured the chambers on my 28 gauge Skeet gun at 2 13/16"
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
02-05-2023, 10:20 AM
|
#7 | ||||||
|
Dean, we would like to see the video. Thanks.
|
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to Bill Murphy For Your Post: |
|
|
|
02-05-2023, 01:01 PM
|
#8 | ||||||
|
Here you go Bill -
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 5 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
02-05-2023, 01:49 PM
|
#9 | |||||||
|
Quote:
Holy crap Dean. What are the details on that amazing little hammer gun? 
|
|||||||
|
|
|
|||||||
|
|
|
|
The pattern? | |
|
02-05-2023, 02:26 PM
|
#10 | ||||||
|
The pattern?
Assuming equal pressures in shells of two different lengths (say 2 1/2” and 2 3/4”), and the shot size and volume of the shot is identical, then what difference does the chamber depth make?
What differences in performance can I expect see in the patterns? Any other interesting differences?
__________________
It's amazing the things people will post when ignorance is celebrated on the internet. Meghan Superczynski, for Boss Shotshells, Bridgman, Michigan |
||||||
|
|
|
||||||
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
