Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Another Cut Barrel Question...
Unread 11-21-2012, 10:43 PM   #1
Member
Chris
Forum Associate
 
Chris_Caile's Avatar

Member Info
 
Join Date: Dec 2011
Posts: 113
Thanks: 14
Thanked 64 Times in 21 Posts

Default Another Cut Barrel Question...

I know this has been gone over 100 times... The Serial books states that the barrel length is 26" but the barrels measure 24 7/8". The wavey lines go all the way to the end of the barrel, could the book be off? Or why would anyone cut just 1" off a barrel?

Thanks-
Chris_Caile is offline   Reply With Quote
Unread 11-21-2012, 10:47 PM   #2
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,957
Thanks: 38,669
Thanked 35,901 Times in 13,165 Posts

Default

Generally speaking, barrels were cut for only a couple of reasons. One was to eliminate some of the choke allowing the gun to shoot more open patterns. The other reason would have been to bob off a section of damaged barrels. I can't even think of another reason. I can't imagine Parker Bros. producing a set of barrels 1/8" less than an even inch length. There are any number of barrel sets that were made a tad longer than an even inch number though.
Dean Romig is offline   Reply With Quote
The Following User Says Thank You to Dean Romig For Your Post:
Unread 11-21-2012, 10:57 PM   #3
Member
David Noble
PGCA Member
 
David Noble's Avatar

Member Info
 
Join Date: Nov 2010
Posts: 1,001
Thanks: 1,623
Thanked 1,235 Times in 441 Posts

Default

Normally the wavy lines do not go all the way to the end. Barrels are cut for numerous reasons but the top three reasons are (1) damage in one of the barrels (2) to reduce the chokes and (3) just to make the barrels shorter. Being that the barrels you mention are cut 1 and 1/8th inch, I would suspect there was damage and that was how much was needed to clean up.
David Noble is offline   Reply With Quote
Unread 11-22-2012, 08:41 AM   #4
Member
Hammer Gun
PGCA Lifetime
Member
 
Gary Carmichael Sr's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 3,697
Thanks: 2,848
Thanked 8,016 Times in 1,706 Posts

Default

I would second that hypothesis!
Gary Carmichael Sr is offline   Reply With Quote
Unread 11-22-2012, 09:48 AM   #5
Member
Holeshot
PGCA Member

Member Info
 
Join Date: May 2010
Posts: 706
Thanks: 1,787
Thanked 269 Times in 159 Posts

Default

The experience I have had with barrels cut 1 inch is awesome. Chokes went from full and mod--- to mod and skeet. Patterns beautiful , and shoots to point of aim. I believe if you remove 2 inches or more , you will probably mess with the point of aim, and have to regulate accordingly. The nice thing about guns with bad or cut barrels is that they are cheap. Bid accordingly. Dave
David Holes is offline   Reply With Quote
The Following User Says Thank You to David Holes For Your Post:
Unread 11-22-2012, 10:19 AM   #6
Member
Brush Buster
PGCA Member
Second Badge
 
Russ Jackson's Avatar

Member Info
 
Join Date: May 2009
Posts: 3,334
Thanks: 3,477
Thanked 3,851 Times in 1,177 Posts

Default

I sure wouldn't argue with anyone about their findings on this , guns with cut barrels seem to all perform a bit differently but I am in Jents court ,I have just not had good luck patterning Barrels that have been cut ! Russ
Russ Jackson is offline   Reply With Quote
Unread 11-22-2012, 10:43 AM   #7
Member
Autumn Daze
PGCA Lifetime
Member
 
Dave Suponski's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,915
Thanks: 4,389
Thanked 4,112 Times in 1,744 Posts

Default

It is my belief that the lack of good patterns becomes more apparent at longer yardages on cut barrel guns. On reason I say this is because of a DH I have that was factory cut from 30" to 26" Its a great skeet/short range gun but leaves me wanting at longer ranges. It patterns great at 25/30 yards but after that not so much.
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker
Dave Suponski is offline   Reply With Quote
Unread 11-23-2012, 11:23 AM   #8
Member
Chris
Forum Associate
 
Chris_Caile's Avatar

Member Info
 
Join Date: Dec 2011
Posts: 113
Thanks: 14
Thanked 64 Times in 21 Posts

Default

Here's a couple of pictures.
Attached Images
File Type: jpg Barrel1.jpg (11.0 KB, 133 views)
File Type: jpg Barrel2.jpg (33.3 KB, 134 views)
Chris_Caile is offline   Reply With Quote
The Following User Says Thank You to Chris_Caile For Your Post:
Unread 11-23-2012, 11:31 AM   #9
Member
Autumn Daze
PGCA Lifetime
Member
 
Dave Suponski's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,915
Thanks: 4,389
Thanked 4,112 Times in 1,744 Posts

Default

They look cut to me Chris.
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker
Dave Suponski is offline   Reply With Quote
Unread 11-23-2012, 11:35 AM   #10
Member
Angel Cruz Ortiz
PGCA Lifetime
Member
 
Angel Cruz's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,625
Thanks: 357
Thanked 1,292 Times in 547 Posts

Default

It looks like that front bead is slighty off center to the right.
__________________
"The Parker Gun"...An Immortal American Classic
Angel Cruz is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:04 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2025, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.