|
02-02-2020, 07:41 PM | #3 | ||||||
|
I saw that. I have examined carefully with naked eye, magnifying glass, held a small bore light at all angles, done all that with the glass, etc. I cannot convince myself that is anything but the tooling or gouging required to fit the trigger guard into the stock. Obvious this was hand fit and not milled out as a modern one would be. Guard fits perfectly flush to the wood, not sunken at all, and I cannot detect the most minute trace of another number having been there. My original thought was this stock was maybe scavenged from another gun?
|
||||||
The Following User Says Thank You to Keith Doty For Your Post: |
02-02-2020, 08:22 PM | #4 | ||||||
|
It is a grade 3 stock. Note the tang channel stamp.
|
||||||
The Following User Says Thank You to Bruce Day For Your Post: |
02-02-2020, 08:43 PM | #5 | ||||||
|
That'sthe mark I referenced Bruce - it's just not very clear but it looks like it might be a 3.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
02-02-2020, 08:58 PM | #6 | ||||||
|
I can absolutely believe that but am trying to figure out how it came to be attached to a grade 4 gun! The water table is clearly marked CH and a 4 appears under the serial number. Serial number on the stock is correct to the rest of the gun and I can see no evidence of "stamped over". I wondered if it happened at Remington ( gun has Remington codes) but Dean feels the drop points and checkering border are wrong for Remington WWII era, feels they are Meriden era.
The area directly under the 2, on close exam, does not appear to be a stamped 3 but a combination of wood character and tool marks. I pulled the trigger guards on a couple of my other hammerless guns and the frame size is clearly stamped, no mistaking it. |
||||||
02-02-2020, 11:57 PM | #7 | ||||||
|
Please post a picture of the entire stock from the side and top looking back from the action. From these pics we should be able to offer a good opinion of a Remington re-stock.
PML |
||||||
The Following User Says Thank You to Patrick Lien For Your Post: |
02-04-2020, 06:14 AM | #8 | ||||||
|
Work near the end of production used available parts . This is not the only C with a stock intended for a D. You will not find a recorded reason for the discrepancy. The plausible explanation is that there was an order for the gun and parts were pulled from bins rather than making new ones. There was a D stock on hand that was a pistol grip and appropriate frame size and that was used.
|
||||||
The Following User Says Thank You to Bruce Day For Your Post: |
02-04-2020, 07:04 AM | #9 | ||||||
|
The Remington repair codes during WWII may well include the replacement stock but that time frame is wrong for the Meriden features of the D grade stock.
My opinion is that IF it was done by Remington during that time frame they used a stock that had been previously taken off of a pre-1937 DH and kept in a used parts inventory. Do you have a PGCA research letter on the gun? It may very well have done at Parker Brothers in Meriden and there may (or may not) be records to support the replacement “as cheap as can” or something to that effect. Your quote “My original thought was this stock was maybe scavenged from another gun.” Is the most likely answer. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
The Following User Says Thank You to Dean Romig For Your Post: |
02-04-2020, 07:44 AM | #10 | ||||||
|
I have seen a number of later (post production) factory replacement stocks with the Remington Grip cap pictured.
I wound say that it is a replacement from during the Remington service timeframe.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
|
|