Hello

[Jeff Elder]

New Parker owner here. I've wanted a Parker since i was 12 years old. Even named my first Chesapeake bay retriever Parker.
Well here I am 45 and finally got one. I went this Christmas to get my girlfriend a present at a jewelry store and the owner offered me a beer after I dropped all that coin on my girl. Well we go to the back and there is a fine looking double gun setting on a table as a center piece. I asked if I could look at it and he said " yes that's a Parker I just got as payment. A guy owed me $1500"
I looked close to see if it was a original Parker and then jokingly said " I'll give you $1600" he said sold and here I am.

My question is it doesn't shoot 2 /34 so as of now I'm shooting RST 2 1/2.
Should I have it modified to shoot 2 3/4 or leave it alone?
Also after having it fit to me we checked the chokes and it is choked full and extra full. Same question should i have chokes opened up?

Thanks for any info
Jeff

[Reggie B]

Personally I would never alter any of my Parkers. But mine are all original condition guns. Not knowing a lot about your gun I can't comment much about it, but I still want to say don't alter it. But that's just me. I encourage you to join the PGCA and become a regular reader of the forums. You will learn so much from fellow members.

[OH Osthaus]

Welcome Jeff

congratulations on your first Parker, how about some details, grade, gauge, barrel length?

please post some pictures

you say "Also after having it fit to me " has the stock been altered?

[Brush Buster]

Hello Jeff ,Welcome to the Forum and I must say I agree with Reggie ,if it isn't tampered with I would leave it as is ! As for the tight chokes many Parker Guns have tight chokes and a lot of us have been shooting Spreader Loads to get around this instead of opening them up ,they will really make a difference !

[Garth Gustafson]

Welcome Jeff,
Congratulations on your 1st Parker! Ditto on the other remarks. Also, if you haven't yet done so go to the PGCA home page. On the left margin scroll down to Collector Info and check out Parker ID, Grades, Mfr Dates, etc. to identify what you have.

Yes, please post some pictures, we'd love to see your new Parker.

[Randy Roberts]

Cannot comment on that Jeff until we know more of the gun including your intended use of it. Good story, did I ever tell ya the one about the guy that went into a jewelry store and came out with a shotgun. There's a good joke in there somewhere...

[Jeff Elder]

Originally Posted by Randy G Roberts

Cannot comment on that Jeff until we know more of the gun including your intended use of it. Good story, did I ever tell ya the one about the guy that went into a jewelry store and came out with a shotgun. There's a good joke in there somewhere...

I intend to shoot dove and when the weather and blind is right gun some ducks with it. It's a 12 gauge 30'inch barrels

[Jay Oliver]

Jeff, As others have suggested I don't think you need to change anything. During it's life that gun had it share 2 3/4" shells through it. Those that know more about it than me can chime in, but the pressure increase of shooting 2 3/4" shells in in 2 5/8" chambers is not considered significant. Most would advise you still would want too shoot low pressure shells in 2 3/4". I would add though that 2 1/2" shells is a safe and prudent approach.

The good news is you already discovered RST shells. They have such a great variety. One of my favorites from them is their 3/4oz 12 gauge loads and you can also get paper hull shells from them which is just too cool. Try out their spreader loads which will help with your tight chokes. You may want to consider getting into reloading at some point as well. I dragged my feet on this forever, but now that I am set up I don't why I was so hesitant.

You didn't mention the gauge or any particulars about your gun. Please let us know and post some pictures.

Good luck with your first Parker!

[Gerald McPherson]

Jeff measure a unfired 2 3/4 shell and a fired 2 3/4 shell then your chamber. Then think about it. This may help. Your chamber may be made for a 2 3/4 inch load.

[Mills]

Welcome Jeff! Ditto the other comments