Chamber size

bob lyons · 03-23-2021, 05:56 PM

What is the consensus on having the chambers lengthen to 2-3/4 on an original Parker?

Dean Romig · 03-23-2021, 05:58 PM

What gauge is your Parker and what is the actual chamber length now?

.

bob lyons · 03-23-2021, 06:04 PM

It is 12 gauge skeet gun posted earlier. I’m sending it back to DelGreco to repair one of the ejectors and was going to have him check the chambers and if they were short 2-9/16 I was thinking on having him lengthen them to 2 3/4.

B. Dudley · 03-23-2021, 06:29 PM

There is not really too much of a point in doing it. The short chambers were intended for 2-3/4” shells.

Dean Romig · 03-23-2021, 07:23 PM

If it’s an original Skeet gun don’t do it!!

I really don’t understand why folks want to lengthen the chambers on any gun - just use the ammo that was intended to be used in it. Why compromise the originality and value of an original gun?!

.

Researcher · 03-23-2021, 09:22 PM

I have tried to make some sense out of the information on Parker Bros. hang tags but I have so few data points it probably isn't meaningful. Generally for 12-gauge guns it appears that if they targeted the gun with 1 1/8 ounce loads they say use 2 5/8 inch shells,

211184 12-gauge, 2 5-8 inch, 1 1-8 ounce.jpg

but if they targeted the gun with 1 1/4 ounce loads the tag says use 2 3/4 inch shell.

216599 12-gauge, 2 3-4 inch, 1 1-4 ounce.jpg

All data points don't fit this. It is very general.

By Remington era the hang tags are pretty general --

240647 12-gauge, 2 3-4 inch.jpg

Parker Bros. certainly was no where near as consistent as Remington Arms Co. was with the loads used to target their hammerless double. Always UMC Load No. 8.

ED J, MORGAN · 03-24-2021, 12:29 PM

The first tag was referring to an unfired shell length , the 2nd, was to a fired shell length. what we call todays shells. go measure an unfired shell it will be shorter than 2 3/4 "

Dean Romig · 03-23-2021, 09:41 PM

I have a 12 gauge DH made in 1898 with 2 9/16” chambers and I shoot 2 3/4” shells in it all day long. And I can not really discern a difference in recoil.
I’ll never have my chambers lengthened and I’ll never change what I shoot in it.

I wonder what kind of ammo and what length ammo was used in these guns before they were ours????

.

Stan Hillis · 03-24-2021, 07:12 AM

It might be worth pointing out that the length of the loaded shell is not the length that matters. It is the length of the fired hull that matters. There is usually a greater difference in the two dimensions on star crimped shells than there is on roll crimped ones, IME.

Also, there is considerable difference between the overall lengths of unfired and fired shells between manufacturers, and loads. IOW, just because the box is marked "2 3/4" in no way means the shell inside opens up to exactly 2 3/4".

Bruce Hering · 03-24-2021, 12:05 PM

Quote:

Originally Posted by Stan Hillis

It might be worth pointing out that the length of the loaded shell is not the length that matters. It is the length of the fired hull that matters. There is usually a greater difference in the two dimensions on star crimped shells than there is on roll crimped ones, IME.

Also, there is considerable difference between the overall lengths of unfired and fired shells between manufacturers, and loads. IOW, just because the box is marked "2 3/4" in no way means the shell inside opens up to exactly 2 3/4".

So true. I had a Mod 12 16 ga with the short chamber and ejection port. It would not eject Winchester ammo but would eject the old low brass Remington... Go figure.