|
 |
 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
08-13-2024, 09:47 AM
|
#3 | ||||||
|
Hmm.
|
||||||
|
|
||||||
 |
 |
 |
| The Following 5 Users Say Thank You to edgarspencer For Your Post: |
|
|
|
08-13-2024, 12:55 PM
|
#4 | |||||||
|
Quote:
|
|||||||
|
|
|||||||
|
|
|
| The Following 4 Users Say Thank You to Ryan Brege For Your Post: |
|
|
|
08-13-2024, 06:24 PM
|
#5 | ||||||
|
Here’s what the authors of The Parker Story reported regarding LOP:
“Skeuse specified the pull length of the Reproductions to be 14 3/8 inches. Well, the Japanese made the guns exactly to that specification, but measured the pull from either the front trigger of two trigger guns or the single trigger of a gun so equipped. The single trigger on the Reproduction was located in the same position as the rear trigger on a two trigger gun. Thus, the single trigger Reproductions may have a pull length that is a little too long for some shooters.” About 14-15 years ago, I had a 20ga. Repro with a single selective trigger that I had converted to double triggers. That conversion added 5/8” to the LOP.
__________________
Wild Skies Since 1951 |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Greg Baehman For Your Post: |
|
|
|
08-13-2024, 06:54 PM
|
#6 | ||||||
|
I know I'm at least 120 years too late, but the only way to measure length of pull is from the middle of the butt to the rear of the trigger guard. The position of the triggers is of no consequence.
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Bill Murphy For Your Post: |
|
|
|
08-13-2024, 10:24 AM
|
#7 | ||||||
|
I usually allow about 3/4" longer effective LOP for a SST.
Bob Jurewicz |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Bob Jurewicz For Your Post: |
|
|
|
08-13-2024, 10:25 AM
|
#8 | ||||||
|
Oh well…
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
08-13-2024, 11:31 AM
|
#9 | ||||||
|
Thanks Bob, that is what I was asking essentially.
__________________
“The difference between mere killing and a glorious sport is the manner in which you do it – over thrilling dogs, in magnificent country and with a near-reverence for the game. - George Bird Evans |
||||||
|
|
|
||||||
|
|
|
|
|
|
08-13-2024, 12:01 PM
|
#10 | ||||||
|
I am not a gun fitter and likely know less than others. However, this concept has always caused me to wonder.
My point is....if one had a proper fitting LOP with a double trigger gun is it common one would require a longer LOP if we changed it to a single trigger where the trigger had the same placement of the former rear trigger? I don't think I would go that route. I believe where I place my face on the gun in relation to the plane of the barrels would cause me more concern than the 3/4" manipulation of my trigger finger. My sense is placing my face further from the frame due to the placement of the trigger within the trigger guard space would seem to alter form more so from a geometry perspective. This is not a statement, it is a question for those more knowledgeable.
__________________
Follow a good dog while carrying a fine shotgun and you will never be uninspired. |
||||||
|
|
|
||||||
|
|
|
 |
|
|
Hybrid Mode