|
07-14-2014, 09:53 PM | #3 | ||||||
|
I'm with Gerry on this one. With the Briley's you can not only outfit it for Quail, but , with a simple change of choke use it for dove, pheasant, etc. I have several guns with interchangeable chokes and love the versatility it gives me.
|
||||||
07-15-2014, 05:48 PM | #4 | ||||||
|
I checked and the cost from Briley is $ 499.00. Thats not that bad considering they will also include 5 Choke tubes @ a value of $250.00
so the way I look at it the shop charge is $ 250.00 forgitting the shipping. The folks also know what they are doing, so it would be quality work. If I do anything it will be with them. Thanks for the advice Pat |
||||||
07-18-2014, 09:08 AM | #5 | ||||||
|
Gentlemen,
I also have a 28 ga Repro in a two barrel set. The IC/M choke had been opened to SK1/SK2. After patterning it extensively, I again had it opened to .001/.003". It is now my "go to" gun for grouse, woodcock and skeet. I understand that tinkering reduces value, but it is a gun and exists for ME to shoot. Why not make the best of it? Not advice, just an opinion. Best Fishes, Steve Kleist Ely, MN |
||||||
The Following User Says Thank You to Steve Kleist For Your Post: |
07-18-2014, 10:02 AM | #6 | ||||||
|
Steve, is the final .001" and .003" opening you had done the result of your patterning it at average grouse and woodcock distances? I have found the factory Q1 & Q2 to be ideal for my grouse and woodcock purposes. What kind of patterns were you getting before the final opening of the chokes?
|
||||||
07-18-2014, 10:54 AM | #7 | ||||||
|
Many years ago I bought a 20 repro with IC/Mod chokes. I really wanted a Q1/Q2 but at the time I could not find one. After shooting the first round of skeet with my new aquisition it was readily apparent that it was choked way too tight for grouse and woodcock so I had it opened to .004 and .008. Following that I patterned it extensively - all at 20 yards. My initial patterning was with my handloads and the open barrel gave me the 30 inch pattern spread I was looking for. I persisted though and bought a box of top end target shells from Win, Federal, and Remington. To say I was surprised with the results is an understatement. The Win AA's delivered an 18 inch pattern, the Rem. STS's 24 inches, and the Federal Gold Medals 32 inches. I thought it could not be so I repeated the patterning on a different day with 10 shots each - same results.
Over the years and many grouse and woodcock I am absolutely thrilled with my decision to open the chokes. However, I shoot only my handloads that I know produce my desired results repeatedly. The moral of the story is that choke makes a difference in pattern performance but so does the choice of ammo you shoot through them. You have to pattern to know what you are getting. |
||||||
The Following 7 Users Say Thank You to Gary Laudermilch For Your Post: |
08-09-2014, 02:59 AM | #8 | ||||||
|
Sent the barells to briley for thin wall chokes after talking to tech dept and they said no problem. My luck big problem barells too thin...they said they could open chokes...my reply
My favorite GUNSMITH ..BILL SCHWARTZ could have done that ...so rather than ship home with no work done...minimum fee plus shipping$ 95.00..so am going to get them to open to skeet and ic..we will see |
||||||
08-09-2014, 09:41 AM | #9 | ||||||
|
Barrels too thin? That's a surprise, since I have heard of others who have had chokes installed with no problem. I guess the solution is to measure bore and outside diameter as well as wall thickness before you ship. Tell them what you have measured by email or phone. By the way, Briley is happy to offer a discount to those who represent themselves as Briley dealers, including many gun clubs.
|
||||||
The Following User Says Thank You to Bill Murphy For Your Post: |
08-12-2014, 06:14 AM | #10 | ||||||
|
'Briley unable to install thinwall chokes in a Parker Repro'
My experience, also ..... |
||||||
|
|