Pressure increase with 2 3/4" shells ?

[Double Trouble]

I know this has been discussed at great length - but what was the percent increase in pressure that Mr. Bell claimed when you shot 2 3/4" shells in the 2 5/8" Parker chambers ? Was it 10%, less ????

The reason for my asking is that I ordered up some NiceShot loads (in 2 3/4" 12 gauge). They are loaded with 1 1/8 oz. of shot, with a claimed velocity of 1250 fps. (That's what was written on the box, however Dan said it was actually 1200 fps, and the low-pressure loading of approx. 7900 - 8000 psig.)


So, my plan was to shoot these duck loads in my 1895 DH 12 gauge, which is in nice shape, #2 frame, with 2 5/8" chambers and seemingly un-honed 32" bores. If Mr. Bell's claim was a 13% increase in pressure, I see no reason to fear a 9,000 psig shell.

Is my logic flawed ?

[Bruce Day]

5 percent.

[Double Trouble]

I can certainly live with that !


Thanks !

[Joe Wood]

There is more pressure variation among shells in the same box than the slight increase shooting longer hulls. Remember, Parker recommended shooting 2 3/4" in their 2 5/8" chambers, feeling if the hull opened partially into the forcing come a better gas seal would be achieved.

[Steve Havener]

The only caution I would have is to check if your 1895 vintage Parker barrels are chambered with conical forcing cones.

[Double Trouble]

Steve: I'll check them tonight.

I assume that conical forcing cones are desirable, instead of the abrupt "step" transition of the earlier chambers - right ?

[Steve Havener]

Originally Posted by John Mazza

Steve: I'll check them tonight.

I assume that conical forcing cones are desirable, instead of the abrupt "step" transition of the earlier chambers - right ?

Your assumption is correct.

[Drew Hause]

It might be worth saving this information

“Long Shells in Short Chambers”, Sherman Bell with technical assistance from Tom Armbrust in “Finding Out for Myself” Part V, Double Gun Journal, Winter 2001

The test barrel was a ‘heavy’ Krieger barrel with piezo-electric transducer at 1” from the breech and an Oehler velocity gauge 2 5/16” from the breech.
Tests were performed:
1. 2 1/2” chamber with a 7/16” forcing cone – “British chamber” (BC)
2. 2 1/2” chamber with a 1 1/4” forcing cone – “Modified British chamber” (MBC)
3. 2 3/4” chamber with a 1” forcing cone – “American Chamber” (AC)

Each load was tested in each chamber at least 5 times.
No significant change in velocity was noted between the 3 test chambers
It was not unusual to have 300-600 psi spread between shots

LOADS
1. 7/8 oz. in Federal plastic hull at 1185 fps (measured in the 2 3/4” chamber)
2. 7/8 oz. in Estate plastic hull at 1206 fps
3. 1 oz. in Federal paper hull at 1137 fps
4. 1 1/8 oz. in Federal paper hull at 1120 fps
5. 1 oz. in Remington plastic hull at 1205 fps
6. 1 1/8 oz. in Winchester plastic hull at 1186 fps
7. 1 1/4 oz. in Federal plastic hull at 1091 fps
8. 1 1/4 oz. in Winchester plastic hull at 1136 fps
9. 1 1/8 oz. with GOEX FFFg in Federal paper at 1184 fps
10. 1 1/8 oz. Bismuth in Federal plastic at 1091 fps


……....BC….….MBC….....AC…..Difference BCvsAC
1…..5725…….5905…..4834……891 psi
2…..6225…….6065…..5009……1216 psi
3…..5865…….5325…..5263……602 psi…..“long cones do reduce pressure”
4…..5845…….5665…..5058……787 psi
5…..7805…….7845…..7577……228 psi
6…11,125….11,045…10,787…338 psi
7…..6892…….6805…..5953……939 psi
8…..8765…….8545…..7870……895 psi
9…..5405…….5265…..4603……802 psi
10…6765…….6365…..6380……385 psi

Interpretation and caution:
1. Results in light British 12b or American small bore barrels may be different.
2. Results in YOUR barrel would require drilling the chamber for the transducer thereby destroying your gun.
3. Paper hulls with star crimps showed little difference compared to plastic hulls. NO roll crimp paper hulls were tested.
4. The increase in pressure comparing 1 oz., 1 1/8 oz., and 1 1/4 oz. loads was similar.
5. Longer cones MAY reduce pressure. This was NOT a comparison of standard 1” with 2 1/2” cones however.
6. “Shooting 2 3/4” shells in 2 1/2” chambers does make them produce more pressure-but in most cases it is less than a 1000 psi increase. I see no reason, related to safety, to modify an original 2 1/2” chambered gun to shoot 2 3/4” shells, if the 2 3/4” load you intend to use would develop pressure that is safe in that gun, when fired in a standard chamber!”
7. “We found that lengthening the forcing cone in a 2 1/2” chamber usually helps mitigate the pressure increase that comes from shooting 2 3/4” or 3” shells in the short chamber.”
8. “Shooting heavy 2 3/4” loads in a light gun is a dumb thing to do. Shooting 3” magnum duck loads is even dumber.”
9. This is not a study of the effect on RECOIL of shooting long shells in short chambers.


Vintage 20g doubles may have chambers shorter than 2 1/2”, and it has been my experience that recoil is markedly increased if 2 3/4” shells are used.

[Bill Murphy]

You might find out whether you have sharp step chambers or gradual forcing cones, but the actual length of the chambers should be entered into the equation. You are looking for expert advice, so you should share that here. I have no idea why you would search out a 1250 fps load to shoot in an 1895 gun. There are other alternatives.

[WmRike]

Back in the sixties gunwriter/engineer G. T. Thomas was worried about this same thing. He ran tests, firing 2.5" and 2.75" shells in 2.5" chambers, measuring pressure 1" and 6" from the breech. His conclusion was that the differences were negligible, and just eyeballing his data, the difference appears to be significantly under 5%.