![]() |
![]() |
![]() |
||||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
ALL Parker bores were honed after boring at the factory.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Dean Romig For Your Post: |
![]() |
Overbore | ![]() |
![]() |
#4 | ||||||
|
![]()
Most, but not all. That's the reason for the question.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
The SBT I currently own has:
.742" bore .703" choke .039" constriction Ser. # 223403 JSH |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to J. Scott Hanes For Your Post: |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
Was wiping down a few today from the safe and measured bores.
SN 238162 SC 34" bore .730 Choke.036 SN 225127 SC 34" bore .731 Choke .031(Extended Forcing Cones) SN 232323 SC 32" bore .732 Choke .033 SN 206107 SC 32" bore .729 Choke .036 SN 190625 SA1 32"bore .742 Choke .044 (Upgrade by Delgrego and Runge) I feel 238162,232323and 206107 have untouched bores. 225127 has original bore and choke but forcing cones have been extended. 190625 has been upgraded (1972) and most likely had bores polished. Hope this helps Paul ![]() |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to PAUL PLUNKETT III For Your Post: |
![]() |
Parker SB Trap bores and chokes | ![]() |
![]() |
#7 | ||||||
|
![]()
Thank you very much Paul. That is exactly the type of information I was hoping to receive. Sounds like you have a very nice collections of SBTs!
Happy Thanksgiving - Scott |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | ||||||
|
![]()
SC 228811 .733 bore .042 choke
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Chuck Bishop For Your Post: |
![]() |
SBT Bore and Choke | ![]() |
![]() |
#9 | ||||||
|
![]()
SB 190xxx .739 with .042 choke...
Trap3 |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 4 Users Say Thank You to Randy Davis For Your Post: |
![]() |
SB Trap Bore and Choke | ![]() |
![]() |
#10 | ||||||
|
![]()
Below is a summary in table format of bore and choke measurements provided by respondents. Worth noting there are some "overbore" guns with really tight chokes. Also, several have relatively more "open" full chokes. Not drawing any conclusions. Thanks to all the responses.
Serial No.Grade Length Bore Choke 191142 SC 32 0.737 0.030 SC 0.730 0.040 SC 0.730 0.040 223403 0.742 0.039 238162 SC 34 0.730 0.036 225127 SC 34 0.731 0.031 232323 SC 32 0.732 0.033 206107 SC 32 0.729 0.036 190625 SA1 32 0.742 0.044 228811 SC 32 0.733 0.042 190xxx SB 0.739 0.042 |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Scott Smith For Your Post: |
![]() |
Thread Tools | |
Display Modes | |
|
|