|
 |
 |
||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||
 |
 |
03-01-2015, 07:11 PM
|
#3 | ||||||
|
Tough question (Perfect) carries a large load .
Can't wait for others to reply. Rufus |
||||||
|
|
||||||
 |
 |
 |
|
|
|
03-01-2015, 07:13 PM
|
#4 | ||||||
|
I already have several of them...
A Grade 1 16 ga. t/a pistol grip hammer gun on the 0-frame with lightening cuts and a fishtail top lever and 28" Laminated Steel barrels choked IC/MOD. Same gun with 26" barrels. Everything else is about identical to the one above but this one has less wear. A Grade 0 16 ga. Lifter with ball grip hammer gun on the 0-frame with lightening cuts with 28" Twist Steel barrels cut back to 24". A 28 ga. VHE on the 00-frame with 26" barrels with skeet in and IC chokes. A DH 20 ga. with PG and 28" Damascus barrels choked IC/MOD and a leather covered pad. A GH 16 ga. on the 0-frame with PG and 26" Damascus barrels choked about CYL & I-CYL. I have a set of 28" 20 ga. Damascus barrels for this gun that are choked M/F. A GHE 16 ga. on the 0-frame with 26" Damascus barrels cut back from 28" choked skeet out and skeet in. I also have a set of 28" Titanic 20 ga. barrels choked about CYL/MOD for this gun. Lemme see... there may be more around here someplace.... 
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
03-01-2015, 07:45 PM
|
#5 | ||||||
|
Grouse? I already have it, like Dean. My 18" ten gauge BH should do the job. I would prefer other guns for a classic gunning experience, but I would prefer the "little gun" if I wanted to actually kill grouse.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
03-01-2015, 07:52 PM
|
#6 | ||||||
|
I was going to post 28 ga GHE skeet gun 26" skeet in skeet out, straight grip, checkered but, beavertail forend, or 16 ga DH 28" 0 frame IC/mod straight grip, splinter forend, double trigger.
But now I want to be Dean's favorite nephew.... 
__________________
"There are two kinds of hunting: ordinary hunting, and ruffed grouse hunting"-Aldo Leopold |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Chad Hefflinger For Your Post: |
|
|
|
03-01-2015, 08:03 PM
|
#7 | ||||||
|
I would like to have alight o frame 16ga, 6lbs. To 6 1/4 lbs max. Will have 28 inch .003/ .012 pg-dt-sf. 14 1/4 1 3/8. 2 3/8 made to order she....(-: sxs ohio
|
||||||
|
|
|
||||||
|
|
|
|
|
|
03-01-2015, 08:26 PM
|
#8 | ||||||
|
OMG .… Dean has all the good guns. Bill is just plain scary. I can see him in his laboritory with Igor hacking that BH to 18". I'm thinking 16 gauge as light as possible.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Mike Franzen For Your Post: |
|
|
|
03-01-2015, 09:09 PM
|
#9 | ||||||
|
GHE 16 gauge on a "0" frame 26" IC in the right and light mod in the left . Straight grip stock , with a skeleton steel buttplate LOP at 13 7/8" . Hopefully to weigh 6 pounds or a red hair under .
If it were a woodcock only thing I would say pretty much the same thing in 28 gauge on a "00" frame but weighing closer to 5 1/4 pounds . Come to think of it the 28 would be about perfecto for southern mule wagon quail hunts except with 28" pipes .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
||||||
|
|
|
||||||
|
|
|
|
|
|
03-01-2015, 09:12 PM
|
#10 | |||||||
|
Quote:
Not my idea of a grouse gun but I bet I could get it shooting handloaded buckshot well enough for driven deer !
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
|||||||
|
|
|
|||||||
|
|
|
 |
|
|
Linear Mode
