Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Clean or Leave alone
Unread 05-23-2014, 09:14 AM   #1
Member
Hammer Gun
PGCA Lifetime
Member
 
Gary Carmichael Sr's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 3,694
Thanks: 2,846
Thanked 8,004 Times in 1,703 Posts

Default Clean or Leave alone

Just a question for the group, I have some 10-A brass shells, in a wooden walnut case most are OK but a few are really dirty and almost black, should I clean them after all they are not pristine if they were I certainly would not touch them, and what should I use to do the cleaning asking for suggestions, Gary
Gary Carmichael Sr is offline   Reply With Quote
Unread 05-23-2014, 09:23 AM   #2
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,932
Thanks: 1,772
Thanked 8,544 Times in 3,345 Posts

Default

i will clean mine in a tumbler like any other brass cartridge, but i intend to load and shoot them

if you are only going to display them - only you can answer the question, do you want them to look new - or old


i would think that Brass-O would do a good job if you only want to clean a few for display
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
Unread 05-23-2014, 05:07 PM   #3
Member
Dick Miller
Forum Associate

Member Info
 
Join Date: Jun 2009
Posts: 44
Thanks: 3
Thanked 14 Times in 6 Posts

Default

Gary,
Try Flitz--- a lot easier to use than BrassO, and leaves a protective coating.
Dick Miller is offline   Reply With Quote
Unread 05-23-2014, 09:18 PM   #4
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 32,854
Thanks: 38,460
Thanked 35,772 Times in 13,110 Posts

Default

just as long as you don't use an abrasive...

My Dad was a coin collector and would soak severely tarnished coins in vinegar if I remember correctly.
Dean Romig is offline   Reply With Quote
Unread 05-23-2014, 11:03 PM   #5
Member
Roundsworth
PGCA Member
 
Mark Landskov's Avatar

Member Info
 
Join Date: Jun 2010
Posts: 1,465
Thanks: 1,553
Thanked 577 Times in 319 Posts

Default

I also use vinegar to clean gnarly brass without abrasives.
__________________
GMC(SW)-USN, Retired
'Earnest Will'
'Desert Shield'
'Desert Storm'
'Southern Watch'
Mark Landskov is offline   Reply With Quote
Unread 05-24-2014, 09:59 AM   #6
Member
Joe Wood
PGCA Member

Member Info
 
Join Date: Nov 2008
Posts: 163
Thanks: 146
Thanked 153 Times in 53 Posts

Default

If they are just for display I suggest leaving them as is. Nothing looks more out of place than antique brass highly polished. With items such as powder flasks it literally destroys the collector value.
Joe Wood is offline   Reply With Quote
Unread 05-24-2014, 10:35 AM   #7
Member
Hammer Gun
PGCA Lifetime
Member
 
Gary Carmichael Sr's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 3,694
Thanks: 2,846
Thanked 8,004 Times in 1,703 Posts

Default

I do not want to polish them just get some of the black off so you can tell they are brass, Do you soak in vinegar overnight? Gary
Gary Carmichael Sr is offline   Reply With Quote
Unread 05-24-2014, 10:51 AM   #8
Member
Roundsworth
PGCA Member
 
Mark Landskov's Avatar

Member Info
 
Join Date: Jun 2010
Posts: 1,465
Thanks: 1,553
Thanked 577 Times in 319 Posts

Default

I have used vinegar to clean old brass cases that were caked with powder residue. I used a rag to wipe the crud off periodically until I was satisfied with the results. The surface of the brass will be clean, but not polished. I submerged the brass and checked on them until I figured they were not going to get any cleaner. Good Luck!
__________________
GMC(SW)-USN, Retired
'Earnest Will'
'Desert Shield'
'Desert Storm'
'Southern Watch'
Mark Landskov is offline   Reply With Quote
Unread 05-24-2014, 10:56 AM   #9
Member
Bindlestiff
PGCA Lifetime
Member
 
Robin Lewis's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,118
Thanks: 703
Thanked 2,940 Times in 870 Posts

Default

May I suggest that before you put them in vinegar that you test the process out on a penny or a scrap piece of copper or brass. That process may not yield what you expect.

If it is simply dirt that you want to remove, so you can tell its old brass but with an aged look, maybe a mild soap or glass cleaner will give the results you want; again - test on something disposable first.

I don't know what look you want but I have used vinegar on pennies when I was young and it will remove the dirt & grime AND any old patina as well. It will make it shine but without the high gloss a polish would give it. It doesn't look old when its done.
Robin Lewis is offline   Reply With Quote
The Following 2 Users Say Thank You to Robin Lewis For Your Post:
Unread 05-24-2014, 05:20 PM   #10
Member
Hammer Gun
PGCA Lifetime
Member
 
Gary Carmichael Sr's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 3,694
Thanks: 2,846
Thanked 8,004 Times in 1,703 Posts

Default

By the way I need 2 more 10-A brass shells to fill my walnut case, any body got spares? Gary
Gary Carmichael Sr is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:07 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2025, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.