|
 |
 |
|||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||
 |
 |
10-19-2010, 05:18 AM
|
#3 | ||||||
|
Well Shane, from your pictures it looks like both guns have been "rode hard" to the point of having been abused. The sixteen certainly looks to be in better condition than the twelve. In fact, I wouldn't even attempt to shoot the twelve at all. The barrels are in poor shape and the ribs are obviously seperating.
The stock on the sixteen presents a couple of questions - one being the Trojan buttplate... another being the lack of a shield in the stock where a grade 1 would have had one.... third being the capped pistol grip if it is a Trojan stock but it doesn't have Trojan checkering.... and finally, if it is a replacement stock, to my mind it is a Parker Bros. stock... very interesting. The serial number 105322 is not in the book so we don't know the original barrel length but it appears to have cut barrels too. Probably down from 26" judging by your choke measurements. |
||||||
|
|
||||||
 |
 |
 |
|
|
|
10-19-2010, 09:13 AM
|
#4 | ||||||
|
I don't have the guns with me as I write this, but do you think the 12 and 16 buttplates could be switched? The guns have been together forever.
About the barrel length--I wonder why someone would only cut two inches off? I'm assuming the sighting bead would have to be removed and the mid-rib drilled and tapped to relocate it? I've seen other pictures of guns that look about the same in albums on here, but they never mention that the barrels have been cut down. I would think these should be cylinder bore if they're cut down, but the one that is perfectly round matches the chart for Improved Cylinder--how is this possible? Sorry, I'm new at this. Thanks for the feedback. It's greatly appreciated. Shane |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-19-2010, 09:19 AM
|
#5 | ||||||
|
There is a whole section on cut barrels in the Parker FAQ section on the home page.
Every barrel that I have seen with out of round muzzle ends patterned poorly. When a person buys an old double shotgun, they are essentially buying barrels. |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-19-2010, 09:28 AM
|
#6 | ||||||
|
Far and away the most common reason for cutting barrels was, for the uninformed of the day, a quick and cheap way of "opening" the chokes. Parker chokes were cut about 4" long - some even as much as 6" so by cutting 2" off the barrels the choke would have lost about 1/2 of its taper.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
10-19-2010, 09:29 AM
|
#7 | ||||||
|
So, basically I got taken for a ride and both the guns are junk now?
 Thanks for the choke explanation. Shane |
||||||
|
|
|
||||||
|
|
|
|
|
|
10-19-2010, 09:30 AM
|
#8 | ||||||
|
We all sincerely hope you didn't pay a lot.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
10-19-2010, 09:32 AM
|
#9 | ||||||
|
I wish someone could just give me a ballpark value on these in $.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
10-19-2010, 09:39 AM
|
#10 | ||||||
|
There are plenty of good 12ga V grade Parkers available for $2000 to $3000, 16ga V's for $2500 to $4000, with unbutchered barrels and stocks and working actions, that may need at most a little gentle cosmetic care. The danger for the novice is picking up a cheap gun from a pile at a cheap gun show and thinking that he has gotten some sort of prize....kind of like buying a high mileage used/abused car that is all clapped out.
The careful potential Parker owner joins the PGCA, buys The Parker Story, makes the acquaintance of a person knowledgeable in Parkers and looks at many at available guns before purchasing.Just like if a person was thinking about getting into old Corvettes or other car that can be a money pit and a trap for the unwary. |
||||||
|
|
|
||||||
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
