|
10-01-2013, 08:26 PM | #3 | ||||||
|
My understanding is that conventional slugs perform best out of loose chokes - say I.C.
|
||||||
10-01-2013, 08:44 PM | #4 | |||||||
|
Quote:
I was more worried about the slug possibly tipping or whatever inside the Cutts chamber .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
|||||||
10-01-2013, 08:47 PM | #5 | ||||||
|
I shot a bunch of Federal 10 gauge factory slugs in a pair of Ithaca MAG-10's I had and a Browning BPS . The BPS did nicely with the IC screw in choke at 50 yards . And as one would expect the pair of Ithaca's with the 32" full choke pipes not so good .
All three did okay with buckshot at 25 and 50 yards .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
||||||
10-01-2013, 10:13 PM | #6 | ||||||
|
I think it is a good test to see if it was attached properly!
|
||||||
10-01-2013, 10:40 PM | #7 | ||||||
|
I would think that it would be safer and perhaps more accurate to remove the choke tube from the Cutts body when shooting slugs. If you do use the choke tube, I would not use a sabot type slug. Over the years I have seen too many blown Cutts. Most were blown by plastic shot cup wads. The wads would get stuck between the muzzle and choke tube. The next shot would blow the end off the Cutts body. These type chokes fell from favor after the advent of fingered shot cup wads. The Poly Choke system prospered in this era until the screw in chokes appeared.
I have seen a few blown Poly's, but I believe most were blown by slugs or large buckshot being fired with the Poly cranked down to extra full. |
||||||
10-01-2013, 11:23 PM | #8 | |||||||
|
Quote:
I had a Model 12 that was made in the mid 50's . It's what was refferred to as a DeLuxe Field . Little better wood , checkering . Anyway when I got it the gun had a poly . I shot quite a few loads of Remington factory Hevi Shot 00 Buck using the full choke setting with no ill effects and very nice patterns out to about 40 yards . To be honest I'd shoot this Remington 48 alot more except for the fact that it's an autoloader and 16 gauge hulls are kinda hard to come by . And it is a PITA to bend over and pick up hulls on the skeet and trap field !
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
|||||||
10-01-2013, 11:26 PM | #9 | ||||||
|
If I had to make a guess I'd say this Cutts has been on my 48 for well over 40 years . I would also be willing to bet the guys that put them on back then "probably" did a better job then a gunsmith now . And thats just based on the fact that they were fairly common back then but one rarely see's one now unless it's a Kolar derivative . So a gunsmith then should have had a heck of alot more practice then a guy now .
__________________
Parker’s , 6.5mm’s , Mannlicher Schoenauer’s and my family in the Philippines ! |
||||||
10-02-2013, 12:08 PM | #10 | ||||||
|
i have a model 12 winchester with a cutts full choke on it..it does pattern really good with bird shot but ive never shot slugs or buck shot in it...you will have to tell us how youre gun does with the slugs i bet it shoots ok...it should do ok out to 50 yards or better in my opinion.. charlie
|
||||||
|
|