|
10-06-2019, 03:34 PM | #3 | ||||||
|
Thanks. I'll get some photos soon.
|
||||||
10-06-2019, 07:52 PM | #4 | ||||||
|
Welcome aboard Young Fella. So you're a shooter and now you have a Parker. Have you been shooting those guns with stacked barrels or the SxS which is the more appropriate configuration ?
|
||||||
10-07-2019, 06:24 AM | #5 | ||||||
|
Randy, this is a side by side. But I haven't been shooting it. My dad originally got the gun after my grandfather died about 1953 and I got it from my dad in the 70's and it went in the closet with my other family hand-me-down. My dad always told me not to shoot it because it had damascus barrels and modern loads could destroy the gun and me. So I've never shot it. I am an active shooter, but not with the Parker.
|
||||||
The Following User Says Thank You to John Black For Your Post: |
10-07-2019, 07:06 AM | #6 | ||||||
|
John,
If you could give us the full serial number we can often be able to tell you how it left the factory. The "Book" was compiled from Parker records and many of the serial numbers are listed. On another note many of us shoot our Damascus and Twist Parkers. Much research has been done along with actually blowing up a few Parkers to determine where and at what pressure these guns would fail. What was found is that Parker Damascus and Fluid Steel guns let go at the breach at the same 31,000 psi +-. That said, those of us that shoot our Damascus and Twist Parkers do so with velocities at 1200 fps or below and liter shot loads i.e.: 1oz in a 12 gauge. RST Shells makes appropriate loads for these fine old guns and pressures are well below 8,000 psi. We're within a year of one another in age and I have my fathers Parker. Other than my memories of him this little Parker is my most precious posession. |
||||||
The Following 2 Users Say Thank You to Harry Collins For Your Post: |
10-07-2019, 07:19 AM | #7 | ||||||
|
Thanks Harry. Truth be told, my oldest son has the Parker. Like my grandfather and father, I have passed it down to him. I have asked him to bring it to me so I can take some photos and get the serial number. Knowing now that I may be able to get proper loads for it, I may have it checked out to see if it is safe to shoot. Any suggestions as to how/where to have it checked? I live in the Tampa, FL area.
|
||||||
10-07-2019, 07:45 AM | #8 | ||||||
|
John,
I am not familiar with gunsmiths in your area that would or wouldn't be knowledgable on old doubles. Most gunsmiths, I fear, are afraid of Damascus and Twist guns because of the liability they may incur. If you google https://sites.google.com/a/damascusk...e.com/www/home you will find great information on these old barrels. Toward the bottom of the page in blue is Barrel Evaluation which will give you what you want to ask the gunsmith to look for. Kindest, Harry |
||||||
The Following User Says Thank You to Harry Collins For Your Post: |
10-07-2019, 09:51 AM | #9 | ||||||
|
Thanks Harry.
__________________
John Black Retired: Every day is a holiday, Every meal a feast, Every hour happy hour. |
||||||
10-07-2019, 02:27 PM | #10 | ||||||
|
Welcome John,
Fortunately there are SXS gunsmiths that have the knowledge and experience to do a proper safety inspection on your Parker. These smiths have been vetted by PGCA members. From the PGCA homepage click on Parker FAQs, see #1 Need a Gunsmith? Good luck in getting your gun back in service and please keep us posted. |
||||||
The Following User Says Thank You to Garth Gustafson For Your Post: |
|
|