|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
05-07-2020, 12:51 PM
|
#3 | ||||||
|
Bores on 10ga guns made before about 1892 have bores of .795-.796.
|
||||||
|
|
||||||
 |
 |
 |
| The Following User Says Thank You to Craig Larter For Your Post: |
|
|
|
05-07-2020, 01:07 PM
|
#4 | ||||||
|
My 10 (1893) has a bore of .783 and choke of .740. Used inside calipers and digital mic. to measure bore, admittedly not the most precise, the choke dimension is precise though. That gives me .43 in both and it shoots tight. Hope this is of some help.
|
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to Daniel Carter For Your Post: |
|
|
|
05-07-2020, 01:26 PM
|
#5 | ||||||
|
Without measuring the bores, the muzzle diameters can allow you to only speculate what the constriction may be. No way of knowing for sure. Oversized bores are not at all uncommon.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Brian Dudley For Your Post: |
|
|
|
05-07-2020, 01:39 PM
|
#6 | ||||||
|
I have a 10 ga lifter circa late 1870' s and bores measure .802 and .805 chokes measure at .760. and actual patterns lead #6 at 35 yards show 90% patterns.
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to George Lang For Your Post: |
|
|
|
05-07-2020, 01:47 PM
|
#7 | ||||||
|
WOW! Nice George!
Does anyone have an accurate bore mic suitable for a 10 gauge they can send me on loan? I have two sets of 10 ga. barrels I have never measured. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
05-07-2020, 01:59 PM
|
#8 | |||||||
|
Quote:
__________________
Progress is the mortal enemy of the Outdoorsman. |
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Pete Lester For Your Post: |
|
|
|
05-07-2020, 02:02 PM
|
#9 | ||||||
|
Thanks Pete - please let me know when that happens.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
05-07-2020, 02:43 PM
|
#10 | ||||||
|
Thanks all.....This is a nice side lever 10 that is hi condition for 2200.00 I have to pass due to the chokes being kinda open. It listed on G.I. I will call the seller and take the hold off. Kenny
|
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
