|
09-01-2016, 08:20 AM | #3 | ||||||
|
SN 79482 was built in 1893 and originally sported 36" barrels per Serialization Book. Look to see if barrels have been shortened. Book is occasionally wrong or there was a second set or barrels or even replacement barrels.
What is the frame size and how heavy are the barrels? Chambers might or might not have been lengthened depending on reliability of gunsmiths measurements. Seek better professional advice and if the gun is OK'd shoot low pressure rounds and not max loads. Erick |
||||||
The Following User Says Thank You to Erick Dorr For Your Post: |
09-01-2016, 08:29 AM | #4 | ||||||
|
Are the current barrels Damascus or fluid steel? It will be stamped into the top rib.
There is a lot to know about these guns before shooting them. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
Advise/info |
09-01-2016, 11:04 AM | #5 | ||||||
|
Advise/info
Thanks to everyone who responded and will take Dean's advise and have the chambers checked again as well as the wall thickness.
Concerning the barrels, they have Parker Bros., Makers, Meriden Conn. Damascus Steel, on the rib. I looked at the end of the barrels, has the bead, and ends look factory to me, unless someone cut them off he did a very good job. I'd say they are factory. As to the serial # on the water table appears 3 different patent dates, 1875, 1887, and 1888. There is the #2 above the ser. # 79432, then the letter G below the number. I looked closely again at the number and pretty sure it is a 3 and not an 8 as I previously stated and appears to have 79432 on the grip below the trigger guard. Sorry about that, but thought it was just worn there and the 3 was an 8. Any suggestions on a gunsmith in the Northwest that would be knowledgeable about these doubles? |
||||||
09-01-2016, 01:49 PM | #6 | ||||||
|
The #2 above the serial number on the water table should be the numerical designation to the "G" grade below the serial number.
If you could post a pic of the end of the bbls. we could give you a better idea if the bbls. have been cut. |
||||||
09-01-2016, 03:00 PM | #7 | ||||||
|
as pointed out above the book (which has been wrong occasionally), says 36" barrels. What are yours?
__________________
"Striving to become the man my dog thinks I am" |
||||||
09-02-2016, 04:02 PM | #8 | ||||||
|
Different gun.
|
||||||
09-04-2016, 08:48 PM | #9 | ||||||
|
thanks again guys, to Big D's question, the barrels are 30 ", checking the ser. # at this website shows manufacture date of 1893 with ser # 79432. Will be looking for SxS gunsmiths to check out this gun for wall thickness and shell length as previously suggested, don't want to move to fast, hunting seasons are opening here in the NW and might have got a little carried away in wanting to shoot it, lol.
|
||||||
11-02-2016, 04:14 PM | #10 | ||||||
|
Just an up date on checking out this Parker. I was able to take it Ljutic, LLC here in Yakima and had one of the smith there check the chokes, chambers, and barrels. They confirm the chambers are 2-3/4, full and full, left measured .031 and the right .034. I think the barrel thickness 8"to 10" down was .030. Subsequently, bought some RST 2/1/2 in shells and shot a round of 16yrd trap, was impressed on how hard the targets broke, didn't shoot a 25 but in the high teens with keeping my head up off the stock to see the target, shot 6 pairs of doubles, broke the 1st bird, but was slow getting my finger on to the back trigger, (didn't want to place fingers on both triggers.) Fun and interesting gun. May try it on some chukers after the elk hunters are done.
|
||||||
|
|