|
03-08-2017, 07:47 AM | #3 | ||||||
|
Dean there are couple things that can cause a hole in the center of the crimp, one is the shot column is too low and another is the cam of MEC loader is not adjusted correctly for the brand of hull you are loading. The wax is way to make a shell with a hole usable.
Adjusting a single stage MEC cam is here:
__________________
Progress is the mortal enemy of the Outdoorsman. |
||||||
The Following User Says Thank You to Pete Lester For Your Post: |
03-08-2017, 07:53 AM | #4 | ||||||
|
Thanks for the video Pete. Maybe now I can quit waxing my crimps.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
The Following User Says Thank You to Dean Romig For Your Post: |
03-08-2017, 10:28 AM | #5 | ||||||
|
Pete and Dean, I've posted this before, but will do it again for anybody who's missed it.
When adjusting the crimp station, the CAM is the LAST thing you adjust. Adjust the crimp starter first, then adjust the seating stem to get the proper depth. When you are getting a correct fold of the crimp petals, and the correct depth set, THEN adjust the cam to eliminate the flare. NOTE The cam adjustment should be set at least 2/3 of the way up, while the other adjustments are being made. Then, and only then, lower the cam enough to eliminate the flare. The roller will not touch the cam (or at least not have any force put on it by the cam) at the very bottom of the stroke. BUT, more cam means the cam will touch the roller and apply force to it longer (further down) in the stroke. The cam has a fairly sharp shoulder or lobe on it. When you start down with the press the roller rolls on the cam (because this part of the cam is circular) and the outer (plastic) part of the die is pushed down by the cam and roller. Until you get around 1/2-3/4 of the way down, everything I have said so far remains true regardless of where the cam is set. However, the cam is rotating as you come down. Eventually the cam rotates to the point when the roller goes past the shoulder on the cam. Past this point the cam is no longer circular. As you come on down the cam puts less and less pressure on the roller. But, the center punch will come on down because it is fastened solidly to the top of the press. If the roller gets past the shoulder of the cam too early in the stroke you will end up with the punch coming on down on the center of the crimp and this tending to squeeze the top of the shell outward. But the plastic part of the die is not coming on down, which means it cannot prevent the top of the shell from flaring outward. It takes a lot of fine tuning to get this just right. There is a reason why Mec adds the final taper die to the Grabber and 9000. Having a separate die that is used strictly to get some taper makes things a lot simpler. The video is ok, but it's a bit miss leading of the purpose of the cam adjustments. Yes too much adjustment down will wrinkle the shell, but first I'd look at the component height in the shell. You need enough shell left over to crimp it. I don't remember right now but I think at least a 1/2" is necessary in a 10ga. Then enough start crimp is necessary - the more the start crimp you have - sometimes the folds almost touching - the more material there is for the final crimp. This alone will sometimes eliminate a hole. Then I do as stated above to round the top of the shell and help close it. Yes, I do keep a candle near by and use it when setting up for different length shells seeing how I have 2 5/8, 2 3/4, and 2 7/8 10 ga hulls.
__________________
Paul Harm |
||||||
The Following 3 Users Say Thank You to Paul Harm For Your Post: |
03-08-2017, 11:19 AM | #6 | ||||||
|
you can also use a hot glue gun for this....charlie
|
||||||
The Following 2 Users Say Thank You to charlie cleveland For Your Post: |
03-08-2017, 11:35 AM | #7 | ||||||
|
Load Gun club in 12 and 20, have a good source and am surprised at the variation in length of hulls from different batches of them. Adjust press in the middle, longer hulls have slight swirl , shorter hulls just closed enough not to leak. In 410 have to adjust when going from Rem. to Win.
|
||||||
The Following User Says Thank You to Daniel Carter For Your Post: |
03-08-2017, 05:30 PM | #8 | ||||||
|
when I load 3/4 oz 12s with # 9 I get a few leakers. Mostly worn out hulls on the last round. Set them aside,for sealing.
I put a little puddle of white Elmers glue on a piece of plastic . Touch it with a pencil point picks up a tiny dot of glue. Touch the hole it seals it with a very sparse dot. You can control the size of the dot with the size of the pencil point. William |
||||||
03-08-2017, 05:45 PM | #9 | ||||||
|
I never cease to be amazed at how we will go thru all sorts of machinations to save a penny using worn out shells that will be shot thru guns for which we have paid thousands .
(Including myself)
__________________
"Striving to become the man my dog thinks I am" |
||||||
03-08-2017, 07:45 PM | #10 | ||||||
|
FWIW I "waxed" a crow with the shell in picture this afternoon Next time I will try use a little more filler wad.
__________________
Progress is the mortal enemy of the Outdoorsman. |
||||||
The Following User Says Thank You to Pete Lester For Your Post: |
|
|