Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Eight bore Parkers
Unread 06-19-2016, 07:54 PM   #1
Member
John Truitt
PGCA Lifetime
Member

Member Info
 
Join Date: Dec 2008
Posts: 965
Thanks: 1,887
Thanked 1,075 Times in 338 Posts

Default Eight bore Parkers

Lightest weight one anyone is aware of?

Smallest frame size they were made in?

Any made with chambers smaller than 3 1/4 or was this considered standard chambers for Parker?

For hammer and hammerless guns. Thanks guys.
John Truitt is offline   Reply With Quote
Unread 06-19-2016, 10:04 PM   #2
Member
charlie cleveland
Forum Associate

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,803 Times in 3,968 Posts

Default

the 3 1/4 inch length was the standard chamber for most gunmakers..i would say that 3 1/4 was the standard for parkers as well but some 8 ga were made in length of up to 4 1/4 length i have a old 8 ga with 4 inch chambers...the 8 ga shells were made in several lengths i have a brass hull that is 3 3/4 inches...as for the lightest 8 ga i have ever heard of is owned by a guy here on the parker site maybe he will chime in and tell its weight..also the smallest frame size i ve heard of in a parker was a 5 frame....charlie....
charlie cleveland is offline   Reply With Quote
The Following 3 Users Say Thank You to charlie cleveland For Your Post:
Unread 06-20-2016, 08:10 AM   #3
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,774
Thanks: 502
Thanked 18,603 Times in 4,770 Posts

Default

Largest i have seen is the 7 frame. Most common size an 8 will be on is the 6. The heaviest weights i have encountered, in the few i have seen, were in the 16 to 17 lb. range.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
Visit Brian Dudley's homepage!
Unread 06-20-2016, 11:49 AM   #4
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,954
Thanks: 6,387
Thanked 9,268 Times in 4,941 Posts

Default

My DH Grade, the only 30" eight in the PGCA research files, weighs just over ten pounds. I would assume it is the lightest original eight out there. Hammerless eights were made on the #6 frame, top lever hammer eights were made on #7 frames. There is the occasional #5 frame, but I think they were all early lifters.
Bill Murphy is offline   Reply With Quote
The Following 3 Users Say Thank You to Bill Murphy For Your Post:
Unread 06-20-2016, 12:08 PM   #5
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,774
Thanks: 502
Thanked 18,603 Times in 4,770 Posts

Default

A 10# 8g would be nice!
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
The Following User Says Thank You to Brian Dudley For Your Post:
Visit Brian Dudley's homepage!
Unread 06-20-2016, 12:25 PM   #6
Member
John Truitt
PGCA Lifetime
Member

Member Info
 
Join Date: Dec 2008
Posts: 965
Thanks: 1,887
Thanked 1,075 Times in 338 Posts

Default

I am aware of one 32" #5 frame d grade top lever gun.

She has great balance and feel.

I assume a #4 frame would be way too small at the breach ball areas to establish a safe OD for an eight.

Thanks for the info guys.
John Truitt is offline   Reply With Quote
Unread 06-20-2016, 01:05 PM   #7
Member
Autumn Daze
PGCA Lifetime
Member
 
Dave Suponski's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 5,896
Thanks: 4,385
Thanked 4,074 Times in 1,731 Posts

Smile

Never say never Doc. We know of a 1 frame 10 bore.
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker
Dave Suponski is offline   Reply With Quote
The Following User Says Thank You to Dave Suponski For Your Post:
Unread 06-20-2016, 06:44 PM   #8
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,954
Thanks: 6,387
Thanked 9,268 Times in 4,941 Posts

Default

Yeah, John, the 30" ten pound eight gauge is a treat, but too short for you. We would establish the #4 frame eight gauge feasibility with calipers and machinist's scales. In my opinion, it can be done. Remember, John, they are hammer guns.
Bill Murphy is offline   Reply With Quote
The Following User Says Thank You to Bill Murphy For Your Post:
Unread 06-20-2016, 07:28 PM   #9
Member
John Truitt
PGCA Lifetime
Member

Member Info
 
Join Date: Dec 2008
Posts: 965
Thanks: 1,887
Thanked 1,075 Times in 338 Posts

Default

Mr Murphy,

It would be interesting to draft it out and see.

IMO a 11 1/2 to 12 lb 34" eight bore would be the ideal combo for me.

Who knows what might be out there.

Your 30" gun sounds like a really interesting piece.
John Truitt is offline   Reply With Quote
Unread 06-20-2016, 07:47 PM   #10
Member
Fishtail
PGCA Lifetime
Member

Member Info
 
Join Date: Feb 2011
Posts: 789
Thanks: 63
Thanked 510 Times in 253 Posts

Default

Before you guys get off the deep end, don't forget that one of the joys of shooting an 8 ga. Parker is the heft that comes along with it. Just like a 28ga should be light and small, an 8 ga. should make you aware from the moment you pick it up that you are wrapping your arms around Big Bertha.
greg conomos is offline   Reply With Quote
The Following 3 Users Say Thank You to greg conomos For Your Post:
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:37 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.