|
 |
 |
|||||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||||
 |
 |
01-08-2021, 09:18 PM
|
#3 | ||||||
|
Rib looks right to me from what little I can see. Like Dean said the frame is correct for a VR gun. Those side panels are another story though, an added embellishment.
|
||||||
|
|
||||||
 |
 |
 |
| The Following 3 Users Say Thank You to Randy G Roberts For Your Post: |
|
|
|
01-08-2021, 10:17 PM
|
#4 | ||||||
|
Yeah, it is right. It just does not have the “V” on the ramp.
It maybe could have been repaired or changed out by Meriden or Remington at some time after original manufacture. Or may be completely original.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Brian Dudley For Your Post: |
|
|
|
01-08-2021, 10:22 PM
|
#5 | ||||||
|
That is one of my(many) Parker goals...to own a vent rib gun
|
||||||
|
|
|
||||||
|
|
|
|
|
|
01-08-2021, 10:22 PM
|
#6 | ||||||
|
The V on the ramp was limited only to one period of Vent Rib production - the earlier period. The other period was as this one is shown, and as it should be for the Remington produced Parker that it is.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
01-08-2021, 10:30 PM
|
#7 | ||||||
|
I could not recall the details on the V off the top of my head. I just knew they were offered both ways.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Brian Dudley For Your Post: |
|
|
|
01-09-2021, 12:09 PM
|
#8 | ||||||
|
The very earliest VR guns had the 'V' or groove milled into the stem of the rib before the flat bridge treatment over the doll's head well was "standardized" by Parker. Most all of these very early VR guns were ordered or built for stock as field guns before Parker offered the VR as a catalog option (I think in 1921-22), and a lot of the early ones had VRs added and were offered to established shooters to test market acceptance. I once owned BHE #183562, a fully-optioned trap/pigeon gun with VR, ST and straight grip which dated I believe to 1918. Howard Miller of Miller Single Trigger fame told me that he remembered seeing this gun at the GAH when his father took him there in 1919 or 1920, and he is convinced that the gun belonged to William McCarty, at that time the president of the newly-formed ITA.
|
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Kevin McCormack For Your Post: |
|
|
|
01-09-2021, 01:57 PM
|
#9 | ||||||
|
I can't believe this 1929 CHE was one of the very earliest VR guns made by Parker Bros.
Ser. No. 230760 was the PGCA Raffle Gun in 2004 or was it 2007...? Anyway, it is a factory vent rib Double Trap with all the options. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
01-09-2021, 04:27 PM
|
#10 | ||||||
|
1934 16 gauge transitional and 1930 20.
__________________
"A man who carries a cat by the tail learns something he can learn in no other way." |
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Reggie Bishop For Your Post: |
 |
|
|
Linear Mode
