|
01-02-2015, 07:59 AM | #3 | ||||||
|
These things happen if you are going to use a gun.
I get people all the time asking about refinishing stocks because they have a single mark in them. I always tell people it is better I wait until you get a few rather than put the money into it for one mark. It is like reprinting your bumper every time you flirt a stone chip. I have not seen the mark in your stock, but I would say you are not effecting the value of the gun in the long run by letting it be. Use the gun, that is what it is there for.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
01-02-2015, 09:42 AM | #4 | ||||||
|
As my gunsmith once told me, "use the gun, there is nothing you can do to it that I can't fix". I've taken that to heart and use my guns now and I have to say I enjoy using them a lot more than them sitting in the gun room and just looking at them!
|
||||||
The Following User Says Thank You to Gerry Addison For Your Post: |
01-02-2015, 09:48 AM | #5 | ||||||
|
Jim, you and your Parker Repro should get out there together and make some good memories. You'll both get scratches.... it's all part of the fun and adds patina to both of you.
|
||||||
The Following User Says Thank You to Dean Romig For Your Post: |
01-02-2015, 10:01 AM | #6 | ||||||
|
Although I agree with all that has been said, no one actually told you that it's pretty much impossible to repair scratches in urethane finished stocks. You could try to put some finish in the scratch with a toothpick and then buff it out after it hardens, but it's doubtful that it will remove the scratch. And you run the risk of adding a large fisheye or halo around the spot if you rub or buff it much.
As you know, your guns won't remain perfect if you use them. Use is what they were made for! |
||||||
01-02-2015, 10:46 AM | #7 | ||||||
|
If your gun has the high gloss finish as most Repros do..the judicious use of 2-part clear epoxy laid in carefully w/a toothpick will make that scratch disappear.
If you have that same finish & have to do a small repair that dulls a spot in the finish - careful use of an unwoven buffing wheel charged w/a very fine abrasive will blend the finish back to it's high gloss glory. Certainly nothing wrong w/caring for your gun but come on..use it and make memories, that is honest wear...don't save it for a museum!! I like an oil finish |
||||||
The Following User Says Thank You to Scot Cardillo For Your Post: |
01-02-2015, 05:11 PM | #8 | ||||||
|
i once had a colt 1883 model 10 ga hammerless gunit was so nice i just never enjoy it finally after years of it setting in the tomb i trade it off for a model 42 winchester 410 really liked that 410 but found a parker 10 ga with them big heavy barrels i liked so well that i traded that 410 for the parker..now i m happy with this beat up old parker.. i ve shot this old ten parker a lot but only fired that safe queen twice in the several years i had it..charlie
|
||||||
01-02-2015, 08:43 PM | #9 | ||||||
|
Look at it as a badge of honor.
|
||||||
01-03-2015, 07:33 AM | #10 | ||||||
|
Guns get scratches. Not using them is as not making love to a beautiful woman because "she's too pretty."
Use it, hunt with it. Once in a while, you will scratch it.....but the pleasure of getting to shoot with it is worth it. You and that gun are going to get older. Enjoy it while you can. |
||||||
The Following 3 Users Say Thank You to Sam Ogle For Your Post: |
|
|