|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
07-26-2021, 08:39 AM
|
#3 | ||||||
|
It is the lowest. Prior lowest was 66223
|
||||||
|
|
||||||
 |
 |
 |
|
|
|
07-26-2021, 09:21 AM
|
#4 | ||||||
|
I can’t enlarge the letter and still retain any resolution. Does it mention original chokes or pellet counts?
That one doesn’t have much going for it except for the “looking back setter” on the right side. Bottom ribs have vent holes drilled - not factory work. Hmmm… .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
07-26-2021, 09:55 AM
|
#5 | ||||||
|
Original barrel length is 28. Would not be surprised if the dealer’s choke measurements are not accurate.
No mention of chokes or pattern info in letter |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Mills Morrison For Your Post: |
|
|
|
07-26-2021, 10:49 AM
|
#6 | ||||||
|
It went back to factory twice! To take dents out, and the first time to refinish barrels.
__________________
Keavin Nelson |
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to keavin nelson For Your Post: |
|
|
|
07-26-2021, 11:12 AM
|
#7 | ||||||
|
Right Keavin but Parker Bros. would not have drilled those vent holes.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
07-26-2021, 11:53 AM
|
#8 | ||||||
|
I look at that gun and just wonder how much shooting it took to make the wood look like that. This gun has had some serious amount of shooting. Gawd, don't you wish guns like this could talk and tell their story?!
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Richard Flanders For Your Post: |
|
|
|
07-26-2021, 11:57 AM
|
#9 | ||||||
|
And good looking wood too
As Dean mentioned though, those holes couldn’t be anything good |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Mills Morrison For Your Post: |
|
|
|
07-26-2021, 12:08 PM
|
#10 | ||||||
|
Some folks who drill vent holes drill tinier holes - I mean how big do they have to be to allow water vapor out?
Then they close them up with a bead of solder and finish over them so they are nearly invisible. That takes an attention to care and details. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
