![]() |
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
A Parker Reproduction case or an Abercrombie and Fitch VC case. One reasonable if you can find it, the other off the charts for cost.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Bill Murphy For Your Post: |
![]() |
![]() |
![]() |
#4 | ||||||
|
![]()
The Repro Case and Cover is the way to go.
Then go on ebay and buy one of the Parker Bros leather labels sold by a seller in the Ukraine. The label will completely cover the Repro label and they look great. Bob Juewicz |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 4 Users Say Thank You to Bob Jurewicz For Your Post: |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
I agree with posts above if you are looking for a stylish case. However, if you do serious travel by air, water or land then I would recommend a modern molded locking case (TSA approved if flying.) There are dozens of youtube videos comparing and testing the many brands (Apache, Pelican, Nanuk, Negrini.) The cost can be less than $100 to almost $1000. They are all function and no style compared to the ones mentioned in earlier posts but will protect your Parkers from serious abuse.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Chris Pope For Your Post: |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
Thanks to all of you for your advice. I plan on getting both a Parker Repro case and a TSA approved travel case as well. Dennis, if your Parker Reproduction case is specifically made for a 20ga. with 26” barrels and has the lock key, I’ll take it. Otherwise, I might look for a bit more. Thanks again.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#7 | ||||||
|
![]()
Kevin,
I'm not sure any case is "made specifically for a 20 gauge". As far as I know, Parker Reproduction cases were made to fit 20 and 28 gauge guns and the snap caps for either will fit. Mine does have a key. Someone chime in please if I'm wrong.
__________________
Nature and four-leggers are God's prescription for what ails the soul. - DWM ![]() |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | ||||||
|
![]()
You may be right, Dennis. I’ve been looking into this a lot and found one on a Parker Repro case that stated the barrel length it can accommodate is 26” with the block in place and 28” without it.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#9 | ||||||
|
![]()
My case is for 26" or shorter barrels. It has no block to remove.
__________________
Nature and four-leggers are God's prescription for what ails the soul. - DWM ![]() |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#10 | ||||||
|
![]()
Perfect! If it’s for 20/28ga., I’ll take it.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|